Bosch DHR-1600A-150A Installation Manual - Page 57

Channels 9 to 16 or 17 to 24

Get Bosch DHR-1600A-150A PDF manuals and user guides View all Bosch DHR-1600A-150A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

Divar XF 6.2.2 Advanced configuration menu | en 57 PTZ - Enable PTZ when a controllable camera is connected. - By default, PTZ is disabled for all inputs. Contrast - Auto contrast - enabled to let the system automatically adjust the contrast for the video input. - Contrast - can be set manually with the slider if Auto contrast is disabled. Enable audio input - Enable Audio input when an audio source is connected. - The Level meter indicates the strength of the audio input signal. - Use the Gain slider to adjust the input sensitivity. Channels 9 to 16 (or 17 to 24) The tabs 9-16 or 17-24 across the top of the menu contain the settings for each of the IP cameras. Note: An IP stream must only be connected to a single channel on a single Divar. There should be no connection to any other device that could influence the settings of the IP device. IP camera If an IP connection has already been configured, the IP address, input type, and stream number is displayed. If a connection has already been established, a video preview appears. 1. Click Setup to configure or change an IP camera connection. - IP address - enter the IP address of the IP camera. - Input - Choose Camera if the channel is connected to a camera or a single-channel encoder. Choose Video line 1-4 if the channel is connected to a multi-channel encoder. - Stream - enter the stream number. - Encoder profile - Displays the encoder profile of the IP device used by the Divar XF. - Username/Password - enter the username and password if applicable. 2. Press OK to confirm settings. It can take a few seconds to establish a successful connection, after which a video preview appears. Input name Enter a name for the selected input. The name can be up to 16 characters long. Enable video input This setting enables (default) or disables the video input. PTZ - Enable PTZ when a controllable camera is connected. - By default, PTZ is disabled for all inputs. Note: Refer to the datasheet for a list of supported IP cameras and encoders. Bosch Security Systems Installation manual F.01U.135.429 | 2.5 | 2009.08

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
Divar XF
Advanced configuration menu | en
57
Bosch Security Systems
Installation manual
F.01U.135.429 | 2.5 | 2009.08
PTZ
–
Enable PTZ when a controllable camera is connected.
–
By default, PTZ is disabled for all inputs.
Contrast
–
Auto contrast
- enabled to let the system automatically adjust the contrast for the video
input.
–
Contrast
- can be set manually with the slider if Auto contrast is disabled.
Enable audio input
–
Enable Audio input
when an audio source is connected.
–
The
Level
meter indicates the strength of the audio input signal.
–
Use the
Gain
slider to adjust the input sensitivity.
6.2.2
Channels 9 to 16 (or 17 to 24)
The tabs 9-16 or 17-24 across the top of the menu contain the settings for each of the IP
cameras.
Note:
An IP stream must only be connected to a single channel on a single Divar. There should be no
connection to any other device that could influence the settings of the IP device.
IP camera
If an IP connection has already been configured, the IP address, input type, and stream
number is displayed. If a connection has already been established, a video preview appears.
1.
Click
Setup
to configure or change an IP camera connection.
–
IP address
- enter the IP address of the IP camera.
–
Input
- Choose
Camera
if the channel is connected to a camera or a single-channel
encoder. Choose
Video line 1-4
if the channel is connected to a multi-channel
encoder.
–
Stream
- enter the stream number.
–
Encoder profile
- Displays the encoder profile of the IP device used by the Divar XF.
–
Username/Password
- enter the username and password if applicable.
2.
Press
OK
to confirm settings.
It can take a few seconds to establish a successful connection, after which a video preview
appears.
Input name
Enter a name for the selected input. The name can be up to 16 characters long.
Enable video input
This setting enables (default) or disables the video input.
PTZ
–
Enable PTZ when a controllable camera is connected.
–
By default, PTZ is disabled for all inputs.
Note:
Refer to the datasheet for a list of supported IP cameras and encoders.