Bosch DHR-1600A-150A Installation Manual - Page 64

Contact, Motion, Video loss

Get Bosch DHR-1600A-150A PDF manuals and user guides View all Bosch DHR-1600A-150A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

64 en | Advanced configuration menu Divar XF 6.7.2 6.7.3 6.7.4 - Follows - activates the beeper, relay, and view only as long as the event is present. Sound beeper on alarm - Enable an audible warning upon an alarm. Sound beeper on video loss - Enable an audible warning upon video loss. Actions when entering this profile Click Edit... to specify pre-positions for PTZ cameras when this profile is started. - Enter a pre-position value from 1-1023 for each of the PTZ cameras that should be moved (PTZ must be enabled for corresponding camera input). Any actions that have been configured are listed. Contact The event behavior can be configured for each of the 16 input contacts in turn. - Check the Enabled box if the input contact should activate an event. - Check the Alarm box if the input contact should activate an alarm. Actions Click Edit... to set up Recording, Monitor and PTZ actions that should be carried out when this contact is active. - Recording: highlight the video channels to be recorded at contact recording settings when this input contact is active (highlight the un-numbered box to select all). A list of the selected channels and their recording properties is shown. - Monitor: highlight the video channels to be displayed on monitors A and B when this input contact is active (highlight the un-numbered box to select all). - PTZ: enter a pre-position value from 1-1023 for each of the PTZ cameras that should be moved (PTZ must be enabled for corresponding camera input). Any actions that have been configured are listed. Motion The event behavior for motion detection can be configured for each video channel in turn. - Check the Enabled box if motion detection should activate a trigger. - Check the Alarm box if motion detection should activate an alarm. Actions Click Edit... to set up Recording, Monitor and PTZ actions that should be carried out when motion is detected. - Recording: highlight the video channels to be recorded at motion recording settings when motion is detected (highlight the un-numbered box to select all). A list of the selected channels and their recording properties is shown. - Monitor: highlight the video channels to be displayed on monitors A and B when motion is detected (highlight the un-numbered box to select all). - PTZ: enter a pre-position value from 1-1023 for each of the PTZ cameras that should be moved (PTZ must be enabled for corresponding camera input). Any actions that have been configured are listed. Video loss The event behavior for video loss signals can be configured for each video channel in turn. - Check the Enabled box for each video channel if video loss should activate a trigger. F.01U.135.429 | 2.5 | 2009.08 Installation manual Bosch Security Systems

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
64
en | Advanced configuration menu
Divar XF
F.01U.135.429 | 2.5 | 2009.08
Installation manual
Bosch Security Systems
–
Follows
- activates the beeper, relay, and view only as long as the event is present.
Sound beeper on alarm
–
Enable an audible warning upon an alarm.
Sound beeper on video loss
–
Enable an audible warning upon video loss.
Actions when entering this profile
Click
Edit...
to specify pre-positions for PTZ cameras when this profile is started.
–
Enter a pre-position value from 1-1023 for each of the PTZ cameras that should be moved
(PTZ must be enabled for corresponding camera input).
Any actions that have been configured are listed.
6.7.2
Contact
The event behavior can be configured for each of the 16 input contacts in turn.
–
Check the
Enabled
box if the input contact should activate an event.
–
Check the
Alarm
box if the input contact should activate an alarm.
Actions
Click
Edit...
to set up
Recording
,
Monitor
and
PTZ
actions that should be carried out when
this contact is active.
–
Recording: highlight the video channels to be recorded at contact recording settings
when this input contact is active (highlight the un-numbered box to select all). A list of
the selected channels and their recording properties is shown.
–
Monitor: highlight the video channels to be displayed on monitors A and B when this
input contact is active (highlight the un-numbered box to select all).
–
PTZ: enter a pre-position value from 1-1023 for each of the PTZ cameras that should be
moved (PTZ must be enabled for corresponding camera input).
Any actions that have been configured are listed.
6.7.3
Motion
The event behavior for motion detection can be configured for each video channel in turn.
–
Check the
Enabled
box if motion detection should activate a trigger.
–
Check the
Alarm
box if motion detection should activate an alarm.
Actions
Click
Edit...
to set up
Recording
,
Monitor
and
PTZ
actions that should be carried out when
motion is detected.
–
Recording: highlight the video channels to be recorded at motion recording settings
when motion is detected (highlight the un-numbered box to select all). A list of the
selected channels and their recording properties is shown.
–
Monitor: highlight the video channels to be displayed on monitors A and B when motion
is detected (highlight the un-numbered box to select all).
–
PTZ: enter a pre-position value from 1-1023 for each of the PTZ cameras that should be
moved (PTZ must be enabled for corresponding camera input).
Any actions that have been configured are listed.
6.7.4
Video loss
The event behavior for video loss signals can be configured for each video channel in turn.
–
Check the
Enabled
box for each video channel if video loss should activate a trigger.