Bose Companion Surround Sound Owner's guide - Page 15

Programming, Companion, controller,

Page 15 highlights

Programming the Companion"' CS-6 controller Your satellite system remote can be set to control the Companion system. To set the satellite remote so that its volume and mute keys control the Companion system instead of the TV, the satellite remote must be programmed to a TV code that is different from that of your TV. The Companion satellite surround sound system is preset for the remote code 000. If you are using an RCA DSS dish and your TV is not being operated by the remote code 000, then you do not need to program the Companion controller. You can use the TV button on the RCA DSS remote to control the Companion system. To set the Companion controller to another RCA DSS remote code or to work with a PRIMESTAR satellite system, follow these steps: 1. Tum the controller off. 2. The red light in the remote sensor goes out to verify that the controller is off. 3. Open the battery compartment cover of your Companion remote control. 4. For RCA DSS remote code 000, switches 3 and 4 are set to off (down). • To set RCA DSS remote code 046, set only switch 3 to on (up). • To set operations with a PRIMESTAR satellite system, set only switch 4 to on (up). Note: Do not change the settings of the factory-preset switches 1, 2, 5, 6, 7, and 8. 5. To program the new code into the controller, at the same time press both the VOLUME UP and SELECT buttons on the back panel of the controller. 6. The remote sensor light flashes to indicate you are programming the controller. 7. Press any key on the Companion remote to send the new code. 8. The remote sensor verifies receiving the code by turning the red light off. lOI n2 3 04 0506070 3 Ii099c"" Figure 14 Remote control switches Switch 3 up for RCA remote code 046 Switch 4 up for PRIMESTAR satellite systems 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25

Programming
the
Companion"'
CS
-6
controller
Your
satellite
system
remote
can
be
set
to
control
the
Companion
system.
To
set
the
satellite
remote
so
that
its
volume
and
mute
keys
control
the
Companion
system
instead
of
the
TV,
the
satellite
remote
must
be
programmed
to
a
TV
code
that
is
different
from
that
of
your
TV.
The
Companion
satellite
surround
sound
system
is
preset
for
the
remote
code
000.
If
you
are
using
an
RCA
DSS
dish
and
your
TV
is
not
being
operated
by
the
remote
code
000,
then
you
do
not
need
to
program
the
Companion
controller.
You
can
use
the
TV
button
on
the
RCA
DSS
remote
to
control
the
Companion
system.
To
set
the
Companion
controller
to
another
RCA
DSS
remote
code
or
to
work
with
a
PRIMESTAR
satellite
system,
follow
these
steps:
1.
Tum
the
controller
off.
2.
The
red
light
in
the
remote
sensor
goes
out
to
verify
that
the
controller
is
off.
3.
Open
the
battery
compartment
cover
of
your
Companion
remote
control.
4.
For
RCA
DSS
remote
code
000,
switches
3
and
4
are
set
to
off
(down).
ā€¢
To
set
RCA
DSS
remote
code
046,
set
only
switch
3
to
on
(up).
ā€¢
To
set
operations
with
a
PRIMESTAR
satellite
system,
set
only
switch
4
to
on
(up).
Note:
Do
not
change
the
settings
of
the
factory
-preset
switches
1,
2,
5,
6,
7,
and
8.
5.
To
program
the
new
code
into
the
controller,
at
the
same
time
press
both
the
VOLUME
UP
and
SELECT
buttons
on
the
back
panel
of
the
controller.
6.
The
remote
sensor
light
flashes
to
indicate
you
are
programming
the
controller.
7.
Press
any
key
on
the
Companion
remote
to
send
the
new
code.
8.
The
remote
sensor
verifies
receiving
the
code
by
turning
the
red
light
off.
Figure
14
Remote
control
switches
lOn 00000
I
2
3
4
5
6
7
3
Switch
3
up
for
RCA
remote
code
046
Ii
0
99cā€œā€
Switch
4
up
for
PRIMESTAR
satellite
systems
15