Brother International BES-1240BC Instruction Manual - English - Page 265

ERROR C7 occurs., Refer to the block diagram showing the cable connections and check

Get Brother International BES-1240BC PDF manuals and user guides View all Brother International BES-1240BC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 265 highlights

Chapter 12 Trouble Shooting Symptom Measures Embroidering data buffer empty, Embroidering start error occurs. NOTE This error may rarely occur according to your PC's performance. If it occurs, check the items shown on the left. • Has the IF cable come off? • Has the RS cable on the PC come off? • Is the PC or machine controller down? Reboot the PC or machine controller. • Are any other software programs running on the PC? • Replace the IF cable. Presser foot down error occurs. • Is the presser foot attached? If not, attach it. • Does it rise and drop immediately? If so, adjust the presser foot sensor. • Does the presser foot rise and make some noise for a while? If so, check to see if connection from the presser foot sensor to the head PCB is proper. Replace the presser foot sensor with a new one. Replace the head PCB with a new one. • Does the presser foot move? If it does not move at all, check to see if connection from the presser foot motor to the head PCB is proper. Replace the presser foot motor with a new one. Replace the head PCB with a new one. ERROR C7 occurs. • Is the lower shaft being tested in the PC test mode? If so, refer to the operation method of the PC test mode and exit the test mode or turn the power off once and on again. • Turn the power off once and on again. If the same error occurs again, replace the main PCB with a new one. Main shaft rotation speed error occurs. • Enter the encoder signal test mode and manually turn the main shaft pulley. If it is abnormally heavy, the main shaft mechanism is faulty. • Refer to the block diagram showing the cable connections and check to see if connection from the main shaft motor to the main PCB is proper. Also check the connection from connectors P6 and P4 of the main PCB to connectors P19 and P12 of the power supply PCB in the box and the connection from connector P11 of the power PCB to the 14v terminal of the power transformer. Cylinder bed position error occurs. Power PCB error occurs. • The bed retract sensor is not adjusted properly. Adjust it properly. • Check to see if connection from connector P16 of the main PCB to connector P10 of the power supply PCB in the control box is proper. • Refer to the block diagram showing the cable connections and check to see if connection from connector P4 of the BC PCB to the power supply PCB in the control box, and connection from connector P9 of the main PCB to connector P3 of the power supply PCB in the control box are proper. • Replace the power supply PCB with a new one. • Replace the main PCB with a new one. BES-940BC • BES-1240BC 263

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
  • 267
  • 268
  • 269
  • 270
  • 271
  • 272
  • 273
  • 274
  • 275
  • 276
BES-940BC • BES-1240BC
263
Chapter 12
Trouble Shooting
Symptom
Measures
Embroidering data buffer empty,
Embroidering start error occurs.
NOTE
This error may rarely occur according
to your PC's performance. If it occurs,
check the items shown on the left.
•
Has the IF cable come off?
•
Has the RS cable on the PC come off?
•
Is the PC or machine controller down?
Reboot the PC or machine controller.
•
Are any other software programs running on the PC?
•
Replace the IF cable.
Presser foot down error occurs.
•
Is the presser foot attached?
If not, attach it.
•
Does it rise and drop immediately?
If so, adjust the presser foot sensor.
•
Does the presser foot rise and make some noise for a while?
If so, check to see if connection from the presser foot sensor to the
head PCB is proper.
Replace the presser foot sensor with a new one.
Replace the head PCB with a new one.
•
Does the presser foot move?
If it does not move at all, check to see if
connection from the presser foot motor to the head PCB is proper.
Replace the presser foot motor with a new one.
Replace the head
PCB with a new one.
ERROR C7 occurs.
•
Is the lower shaft being tested in the PC test mode?
If so, refer to the operation method of the PC test mode and exit the
test mode or turn the power off once and on again.
•
Turn the power off once and on again.
If the same error occurs again,
replace the main PCB with a new one.
Main shaft rotation speed error oc-
curs.
•
Enter the encoder signal test mode and manually turn the main shaft
pulley.
If it is abnormally heavy, the main shaft mechanism is faulty.
•
Refer to the block diagram showing the cable connections and check
to see if connection from the main shaft motor to the main PCB is
proper.
Also check the connection from connectors P6 and P4 of the
main PCB to connectors P19 and P12 of the power supply PCB in the
box and the connection from connector P11 of the power PCB to the
14v terminal of the power transformer.
Cylinder bed position error occurs.
•
The bed retract sensor is not adjusted properly.
Adjust it properly.
Power PCB error occurs.
•
Check to see if connection from connector P16 of the main PCB to
connector P10 of the power supply PCB in the control box is proper.
•
Refer to the block diagram showing the cable connections and check
to see if connection from connector P4 of the BC PCB to the power
supply PCB in the control box, and connection from connector P9 of
the main PCB to connector P3 of the power supply PCB in the control
box are proper.
•
Replace the power supply PCB with a new one.
•
Replace the main PCB with a new one.