Brother International DCP-7065DN Users Manual - English - Page 55

Start, Error Message, Cause, Action, Duplex Disabled, EL Error, Fuser Error, Init Unable XX - user manual

Get Brother International DCP-7065DN PDF manuals and user guides
UPC - 012502627128
View all Brother International DCP-7065DN manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

Troubleshooting Error Message Cause Action Duplex Disabled The duplex tray is removed or is Carefully put the duplex tray into the not properly installed. machine until it clicks into place. The back of the machine is not closed completely. Close the back cover of the machine. EL Error The machine has a mechanical Open the front cover and close it again. problem. Fuser Error The temperature of the fuser unit does not rise to a specified temperature within the specified time. Turn the power switch off, wait a few seconds, and then turn it on again. Leave the machine for 15 minutes with the power turned on. The fuser unit is too hot. Init Unable XX The machine has a mechanical problem.  Disconnect the machine from the power for several minutes and then reconnect it.  If the problem continues, call Brother Customer Service. Jam Duplex The paper is jammed in the duplex tray at the back of the machine. (See Paper is jammed in the Duplex Tray on page 52.) Jam Inside The paper is jammed inside the (See Paper is jammed inside the machine machine. on page 48.) B Jam Rear The paper is jammed in the back (See Paper is jammed at the back of the of the machine. machine on page 46.) Jam Tray The paper is jammed in the paper (See Paper is jammed in the standard paper tray of the machine. tray on page 45.) No Paper The machine is out of paper or paper is not properly loaded in the paper tray. Do one of the following:  Refill the paper in the paper tray and press Start.  Remove the paper and load it again. Then press Start.  If the problem is not resolved, the paper pick-up roller may need to be cleaned. Clean the paper pick-up roller. (See Cleaning the paper pick-up rollers in Appendix A of the Advanced User's Guide.) Manual Feed Manual feed was selected as the Place a sheet of paper in the manual feed paper source when there was no slot. (See Loading paper in the manual feed paper in the manual feed slot. slot on page 10.) No Toner The toner cartridge is not installed Pull out the drum unit. Take out the toner correctly. cartridge and then put it back into the drum unit. 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
Troubleshooting
41
B
Duplex Disabled
The duplex tray is removed or is
not properly installed.
Carefully put the duplex tray into the
machine until it clicks into place.
The back of the machine is not
closed completely.
Close the back cover of the machine.
EL Error
The machine has a mechanical
problem.
Open the front cover and close it again.
Fuser Error
The temperature of the fuser unit
does not rise to a specified
temperature within the specified
time.
Turn the power switch off, wait a few
seconds, and then turn it on again. Leave
the machine for 15 minutes with the power
turned on.
The fuser unit is too hot.
Init Unable XX
The machine has a mechanical
problem.
Disconnect the machine from the
power
for several minutes and then reconnect
it.
If the problem continues, call Brother
Customer Service.
Jam Duplex
The paper is jammed in the
duplex tray at the back of the
machine.
(See
Paper is jammed in the Duplex Tray
on page 52.)
Jam Inside
The paper is jammed inside the
machine.
(See
Paper is jammed inside the machine
on page 48.)
Jam Rear
The paper is jammed in the back
of the machine.
(See
Paper is jammed at the back of the
machine
on page 46.)
Jam Tray
The paper is jammed in the paper
tray of the machine.
(See
Paper is jammed in the standard paper
tray
on page 45.)
No Paper
The machine is out of paper or
paper is not properly loaded in the
paper tray.
Do one of the following:
Refill the paper in the paper tray and
press
Start
.
Remove the paper and load it again.
Then press
Start
.
If the problem is not resolved, the paper
pick-up roller may need to be cleaned.
Clean the paper pick-up roller. (See
Cleaning the paper pick-up rollers
in
Appendix A
of the
Advanced User's
Guide
.)
Manual Feed
Manual feed was selected as the
paper source when there was no
paper in the manual feed slot.
Place a sheet of paper in the manual feed
slot. (See
Loading paper in the manual feed
slot
on page 10.)
No Toner
The toner cartridge is not installed
correctly.
Pull out the drum unit. Take out the toner
cartridge and then put it back into the drum
unit.
Error Message
Cause
Action