Bushnell Stableview 10x35 Owner's Manual - Page 11

Stabilization Mode Switching, Mode Operation - image stabilizing binoculars

Get Bushnell Stableview 10x35 PDF manuals and user guides View all Bushnell Stableview 10x35 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

STABILIZATION OPERATION When you press the Power button the first time, the LED lights in orange, and the binoculars go to Standby mode. Your Bushnell StableView binoculars go through an internal system check and take about five seconds to stabilize their performance. Then, turn the stabilization lever to the ACTIVE position. The LED turns green, indicating that the stabilization feature is active. Power Button Stabilization Lever LED Indicator Stabilization Mode Switching There are 2 stabilization modes: the regular stabilization LED mode (normal mode), and enhanced stabilization mode (fine mode).During use in normal mode, you can switch to fine mode. In fine mode, cancellation of rapid vibration is improved over normal mode, achieving sharp, hand held Lit in orange Lit in green Flashing in orange/green Lit in red Flashing in red Off images. However, as panning (tracking of the target) motion is not counteracted in fine mode, it is recommended that you first locate the target in normal mode, then switch to fine mode for observation. Status Standby (stabilization off ) Stabilization active (normal) Fine mode Batteries should be replaced System problem Power Off Mode Operation Use the power button to switch the stabilization modes. During normal mode operation (Power ON; stabilization lever at ACTIVE position), hold down the power button briefly then release to operate in fine mode. 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
LED
Indicator
Stabilization Lever
Power Button
LED
Status
Lit in orange
Standby (stabilization off)
Lit in green
Stabilization active (normal)
Flashing in orange/green
Fine mode
Lit in red
Batteries should be replaced
Flashing in red
System problem
Off
Power Off
STABILIZATION OPERATION
When you press the Power button the first time, the LED lights in
orange, and the binoculars go to Standby mode. Your Bushnell StableView
binoculars go through an internal system check and take about five
seconds to stabilize their performance.
Then, turn the stabilization lever to the ACTIVE position. The LED turns
green, indicating that the stabilization feature is active.
Stabilization Mode Switching
There are 2 stabilization modes: the regular stabilization
mode (normal mode), and enhanced stabilization mode (fine
mode).During use in normal mode, you can switch to fine
mode. In fine mode, cancellation of rapid vibration is
improved over normal mode, achieving sharp, hand held
images. However, as panning (tracking of the target) motion
is not counteracted in fine mode, it is recommended that you first locate the
target in normal mode, then switch to fine mode for observation.
Mode Operation
Use the power button to switch the stabilization modes.
During normal mode operation (Power ON; stabilization lever at
ACTIVE position), hold down the power button briefly then release to
operate in fine mode.
5