Bushnell Stableview 10x35 Owner's Manual - Page 5

Quick Reference Guide - image stabilized binoculars

Get Bushnell Stableview 10x35 PDF manuals and user guides View all Bushnell Stableview 10x35 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

QUICK REFERENCE GUIDE 1) Load two AA alkaline batteries into the compartment on the handstrap. 2) Press the Power button (a) to turn on. The electronic system will start up, and the binoculars will go to Standby mode after about five seconds. (LED indicator stops blinking 3) Adjust the eyepiece spacing (b) to match the distance between your two eyes. 4) Use your left eye as you adjust the focus control knob (c). When the image becomes sharp, use your right eye and turn the diopter adjustment ring (d) to focus for the right eye. Once you have performed the diopter correction, use only the control knob (c) to check focus again. 5) Turn the stabilization lever (e) to the ACTIVE position to activate the stabilization feature. 6) Press the power button briefly to change to fine mode, which is more effective at countering hand shake. Tap the power button again to return to normal mode. 7) When finished, turn the stabilization lever (e) to the HOLD position and press the Power button (a) to turn off. LED Status Lit in orange Standby (stabilization off ) Lit in green Stabilization active (normal) Flashing in orange/green Fine mode Lit in red Batteries should be replaced Flashing in red System problem Off Power Off

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
QUICK REFERENCE GUIDE
1) Load two AA alkaline batteries into the compartment on the handstrap.
2) Press the Power button (a) to turn on. The electronic system will start up, and the binoculars will go
to Standby mode after about five seconds. (LED indicator stops blinking
3) Adjust the eyepiece spacing (b) to match the distance between your two eyes.
4) Use your left eye as you adjust the focus control knob (c). When the image becomes sharp, use your
right eye and turn the diopter adjustment ring (d) to focus for the right eye. Once you have performed
the diopter correction, use only the control knob (c) to check focus again.
5) Turn the stabilization lever (e) to the ACTIVE position to activate the stabilization feature.
6) Press the power button briefly to change to fine mode, which is more effective at countering hand
shake. Tap the power button again to return to normal mode.
7) When finished, turn the stabilization lever (e) to the HOLD position and press the Power button (a)
to turn off.
LED
Status
Lit in orange
Standby (stabilization off )
Lit in green
Stabilization active (normal)
Flashing in orange/green Fine mode
Lit in red
Batteries should be replaced
Flashing in red
System problem
Off
Power Off