Canon 3200B002 User Manual

Canon 3200B002 Manual

Get Canon 3200B002 PDF manuals and user guides View all Canon 3200B002 manuals
Add to My Manuals
Save this manual to your list of manuals

Canon 3200B002 manual content summary:

  • Canon 3200B002 | User Manual - Page 1
    User Manual Please read this manual before using the scanner. After you finish reading this manual, keep it in a safe place for future reference.
  • Canon 3200B002 | User Manual - Page 2
    Document Scanner, Model M11067 This device complies with Part accordance with the instructions, may cause equipment off and on, the user is encouraged to try to manual. If such changes or modifications should be made, you could be required to stop operation of the equipment. Canon U.S.A. Inc. One Canon
  • Canon 3200B002 | User Manual - Page 3
    Document Scanner. DR-7090C: Model M11067 Trademarks • Canon and the Canon logo are registered trademarks of Canon Inc. in the United States and may also be trademarks or registered trademarks in other countries. • imageFORMULA 2008 by CANON ELECTRONICS INC. All rights reserved. No part of this
  • Canon 3200B002 | User Manual - Page 4
    , and troubleshooting. The Software section describes how to use the ISIS/ TWAIN driver with the scanner, and how to set up job registration tools. CapturePerfect 3.0 Operation Guide (Electronic Manual) This is the operation guide for CapturePerfect 3.0, the Canon document scanner application
  • Canon 3200B002 | User Manual - Page 5
    DR-7090C Chapter 4 User Modes Describes the User Mode and other functions Chapter 5 Maintenance Describes routine cleaning and roller replacement Chapter 6 Practical Examples Describes displayed messages and troubleshooting solutions Chapter 7 Appendix Provides a list of specifications and support
  • Canon 3200B002 | User Manual - Page 6
    User Manual Hardware Please read this manual before using the scanner. After you finish reading this manual, keep it in a safe place for future reference.
  • Canon 3200B002 | User Manual - Page 7
    and Functions of Parts 1-11 Feeder 1-11 Flatbed 1-11 Rear 1-12 Operation Panel 1-12 4. Optional Products 1-14 Stamp Unit 1-14 Chapter 2 Setup 1. Setup Procedures 2-2 2. Installation Requirements 2-3 3. Software Installation 2-4 About the Setup Menu 2-4 4. Connecting the Scanner to the
  • Canon 3200B002 | User Manual - Page 8
    2. Troubleshooting 6-5 Trouble Categories 6-5 Problem and Solution 6-5 3. Uninstalling the Software 6-11 Uninstalling the ISIS/TWAIN Driver 6-11 Chapter 7 Appendix 1. Specifications 7-2 Specifications for the Scanner 7-2 Options 7-3 Consumables 7-3 External Dimensions 7-4 2. Index 7-5
  • Canon 3200B002 | User Manual - Page 9
    Braces 1-3 Power 1-3 Checking the Rear Cables 1-4 Opening and Closing the Feeder 1-4 Moving the Scanner 1-4 Handling 1-5 Disposal 1-7 2. Features 1-8 3. Names and Functions of Parts 1-11 Feeder 1-11 Flatbed 1-11 Rear 1-12 Operation Panel 1-12 4. Optional Products 1-14 Stamp Unit 1-14
  • Canon 3200B002 | User Manual - Page 10
    Scanner 1. Important Safety Instructions To ensure the safe operation of this scanner, be sure to read the safety warnings and precautions described below. Installation Location The performance of this scanner have negative effects on the inner parts of the scanner. ● Avoid warm or humid locations
  • Canon 3200B002 | User Manual - Page 11
    60 Hz or 220-240 V, 50/60 Hz, depending on your region). ● Do not use the scanner with a power supply that is not rated for the specified voltage. Doing so might cause fire or the power supply, contact your local authorized Canon dealer or service representative for further information. 1-3
  • Canon 3200B002 | User Manual - Page 12
    Cables Before connecting to the computer, make sure that cable connectors to are properly connected at the rear of the scanner. Chapter 1 Before You Start Using the Scanner ● Close the feeder carefully and slowly, taking care to avoid pinching your fingers. Opening and Closing the Feeder ● Open
  • Canon 3200B002 | User Manual - Page 13
    cord, and do not pull or excessively bend the power cord. ■ Never connect the power cord when your hands are wet. ■ Do not connect the scanner to a multiplug power strip. ■ Do not knot or coil the power cord, as this may result in a fire or electric shock. When connecting the power
  • Canon 3200B002 | User Manual - Page 14
    your local authorized Canon dealer or service representative to have the unit serviced. ■ Before moving the scanner, make sure to turn the power switch OFF, and disconnect the power plug from the power outlet. ■ Notice to Cardiac Pacemaker Users
  • Canon 3200B002 | User Manual - Page 15
    on the feeder. Doing so might damage the glass and create the risk of a malfunction or personal injury. ■ Never place any object other than documents to be scanned onto the scanner's flatbed (platen glass). Doing so might result in a malfunction or personal injury. Disposal ● When disposing of this
  • Canon 3200B002 | User Manual - Page 16
    Features The main features of the DR-7090C are described below. Scanner Features ● High-speed scanning The feeder supports scanning of LTR/A4-size documents at speeds up to 70 pages per minute. ● Single-pass duplex (two-side) scanning When scanning two-sided documents with the feeder, the front and
  • Canon 3200B002 | User Manual - Page 17
    detection functions may not perform properly depending on the document type. Image Processing ● Deskew The scanner straightens an image when it recognizes from the image that the document page was fed askew. Skewed Image Deskewed Image IMPORTANT Deskew may not function properly when scanning only
  • Canon 3200B002 | User Manual - Page 18
    on the software application, can create two images with different scanning conditions from a single scan pass. However, this function is only available when using CapturePerfect 3.0 (supplied with the scanner) or another application program that supports the MultiStream function. Document to be
  • Canon 3200B002 | User Manual - Page 19
    Chapter 1 Before You Start Using the Scanner 3. Names and Functions of Parts The names and functions of the DR-7090C parts are shown below. Feeder Flatbed a Feeder Cover Open this cover to clear document jams and clean the rollers. (See p. 3-22 and p. 5-6.) b Opening Lever Operate this release
  • Canon 3200B002 | User Manual - Page 20
    scanner and create the risk of fire. a Menu Key Press this key to cycle the display through the various user modes, as shown below. (See "About the User - b y Mo d e 240 60 [ 10 ] USB Sh o r t Pa c k e t [ ON ] OF F Japanese ON [ OFF ] SCS I Sp e e d [ 20 ] 10 5 D i sp l ay Con t r as
  • Canon 3200B002 | User Manual - Page 21
    displayed starts the scanning of the document and forwards the scanned image to the destination registered for the job. f New File Key This key is active for applications that support batch separation. This key lights from the counter display area. Chapter 1 Before You Start Using the Scanner 1-13
  • Canon 3200B002 | User Manual - Page 22
    Chapter 1 Before You Start Using the Scanner 4. Optional Products The following options can be purchased and used on the DR-7090C, if they are necessary. Contact your sales representative. Stamp Unit The stamp unit affixes a stamp on document pages that are scanned using the feeder. The
  • Canon 3200B002 | User Manual - Page 23
    Chapter 2 Setup 1. Setup Procedures 2-2 2. Installation Requirements 2-3 3. Software Installation 2-4 About the Setup Menu 2-4 4. Connecting the Scanner to the Computer ....... 2-6 Interface Connector Locations 2-6 Using a USB Connection 2-6 Using a SCSI Connection 2-7 5. Turning the Power ON
  • Canon 3200B002 | User Manual - Page 24
    you connect the scanner to the computer before installing the software, a wizard screen such as the one shown below will appear when you turn the scanner ON. In this case, click [Cancel] to close the wizard screen, and then turn the scanner OFF. • Windows 2000 • Windows XP • Windows Vista Chapter
  • Canon 3200B002 | User Manual - Page 25
    transmission may take a long time. • Even if the computer satisfies the recommended specifications, the scanning speed may vary, depending on the scan settings. • The ISIS/TWAIN Drivers provided with the scanner do not necessarily operate on all ISIS- or TWAIN-compatible applications. For details
  • Canon 3200B002 | User Manual - Page 26
    when installing software, log in using an account with Administrator privileges. • When using Windows Vista, the "User Account Control" dialog box may appear. In this case, enter your login user password for Administrator privileges, and click [OK]. Hint See the Easy Start Guide for instructions on
  • Canon 3200B002 | User Manual - Page 27
    . Click [Install] to install the selected software. ■ The Read Manual Screen From this screen you can select one of the supplied electronic manuals to read: the Easy Start Guide (a printed copy is also supplied), the Reference Guide, the User Manual (this manual), or the CapturePerfect 3.0 Operation
  • Canon 3200B002 | User Manual - Page 28
    Computer There are two methods for connecting the DR-7090C scanner to a computer: a USB connection to a standard computer environment. Interface Connector Locations The USB port and SCSI connector are located on the scanner as shown below. 2. Connect the power cord into an AC outlet. b SCSI ID
  • Canon 3200B002 | User Manual - Page 29
    computer is turned OFF before connecting the SCSI cable. If the cable is connected while the computer is on, the scanner may not be properly recognized by the computer. 1. Shut down Windows and turn the computer's power OFF. 2. Connect the supplied power cord into the power connector on the back of
  • Canon 3200B002 | User Manual - Page 30
    are set to OFF. Terminator OFF Terminator ON Set the terminator switch on the scanner to OFF. In such a connection, set the terminator on the last connected SCSI device to ON. Terminator ON or terminator plug connected Terminator OFF
  • Canon 3200B002 | User Manual - Page 31
    1. Make sure that the scanner and computer are connected properly. 2. Turn ON the scanner. 3. Turn ON the computer. 4. Log on to Windows as an Administrator. 5. Windows automatically recognizes the scanner and performs the device driver installation. • Windows 2000 • Windows XP • Windows Vista 2-9
  • Canon 3200B002 | User Manual - Page 32
    DR-7090C device driver is installed in Device Manager under [Imaging Devices] as [CANON DR-7090C USB] or [CANON DR-7090C SCSI]. • With Windows Windows 2000, open [System] and click [Device Manager] on the Hardware tab sheet. - With Windows tab sheet. - With Windows Vista, open [System Maintenance
  • Canon 3200B002 | User Manual - Page 33
    Chapter 3 Basic Operation 1. Documents 3-2 Types of Documents 3-2 Feeder Capacity 3-3 2. Placing Documents onto the Scanner 3-4 Loading a Document into the Feeder 3-4 Positioning a Document on the Flatbed (Platen Glass 3-5 3. Document Feeding 3-8 Scan Procedure 3-8 4. Scanning 3-11 About
  • Canon 3200B002 | User Manual - Page 34
    and then scan the documents one by one. (See "About the User Modes" on p. 4-2.) • Before scanning documents that contain pasted artwork, make sure that the ink or paste on the pages is thoroughly dry. If the documents are scanned with the ink or paste still wet, the scanner may malfunction. • If you
  • Canon 3200B002 | User Manual - Page 35
    • To avoid paper jams, damage to documents, and a scanner malfunction, do not feed the following types of paper. For such documents, scan one page at a time from the flatbed (platen glass). Wrinkled or creased paper Carbon-backed paper Curled paper Coated paper Torn paper Paper with clips or
  • Canon 3200B002 | User Manual - Page 36
    Chapter 3 Basic Operation 2. Placing Documents onto the Scanner This section describes how to load documents into the feeder and how to position a document page on the flatbed (platen glass) for scanning. CAUTION Handle documents with care. Improper handling of paper can cause paper cuts or other
  • Canon 3200B002 | User Manual - Page 37
    of paper in the document eject tray before scanning the document. Chapter 3 Basic Operation Positioning a Document on the Flatbed (Platen Glass) Use the following procedure to scan on the flatbed (platen glass) when scanning a book, thick document, very thin document, OHP (overhead transparency) or
  • Canon 3200B002 | User Manual - Page 38
    hard on the feeder. Doing so might damage the glass and create the risk of malfunction or personal injury. 4. Open the feeder and remove the document from the flatbed (platen glass). IMPORTANT Open the feeder carefully and slowly, taking care to avoid letting the feeder fall over backwards. 3-6
  • Canon 3200B002 | User Manual - Page 39
    the feeder a, pull the feeder down and forward b. Chapter 3 Basic Operation 3. Set the thick document or book on the flatbed (platen glass) and hold the feeder lightly while scanning. 2" (50 mm) Book or Thick document 4. To return the feeder to its original position, open it all the way a, then
  • Canon 3200B002 | User Manual - Page 40
    side is set to [Auto] in the scanner settings screen, documents placed in the feeder will be scanned. If there are no documents in the feeder, the flatbed will be scanned. ■ Standard Feeding To use the standard feeding mode, instruct the scanner to start from the application. 1. Select [Standard
  • Canon 3200B002 | User Manual - Page 41
    green. Chapter 3 Basic Operation 3. Place the document onto the scanner. IMPORTANT See "Placing Documents onto the Scanner" on p. 3-4 for information about placing documents onto the scanner. 4. Press Start. 5. When scanning of the document is complete, the scanner goes into the Ready Mode. Hint If
  • Canon 3200B002 | User Manual - Page 42
    you place a document on the flatbed and press the Start key, the document on the flatbed will be scanned. The scanner detects the documents, and scanning starts. IMPORTANT See "Placing Documents onto the Scanner" on p. 3-4 for information about placing documents onto the scanner. 4. When scanning
  • Canon 3200B002 | User Manual - Page 43
    program such as the CapturePerfect 3.0 software included with the scanner, or directly from the control panel of the DR-7090C, using the Job Function. Events Function" on p. 3-13.) 2. From the Windows task bar, click [Start] ➔ click [All Programs] ➔ [Canon DR-7090C] ➔ [Job Registration Tool]. 3-11
  • Canon 3200B002 | User Manual - Page 44
    "Placing Documents onto the Scanner" on p. 3-4. 7. Press the Start key. The image file is forwarded in accordance with the selected job. 8. When scanning of the document is complete, press the Stop key to exit the Job Mode. Hint If the Job Mode is not operating correctly, see "Troubleshooting" on
  • Canon 3200B002 | User Manual - Page 45
    Panel]. Chapter 3 Basic Operation 3. Select [Canon DR-7090C] and click [Properties]. 2. Double-click [Scanners and Cameras]. 4. Click the [Events] tab. The Scanners and Cameras dialog box appears. Hint The dialog box that appears may vary depending on the Windows version you are using. 3-13
  • Canon 3200B002 | User Manual - Page 46
    Restart Windows. ■ Scanning with CapturePerfect The following three scanning methods are available from the CapturePerfect Scan menu. Scan Batch to Printer Scan Batch to File Prints scanned images Saves scanned images as files in on a specified printer a specified folder (Network) DR-7090C Scan
  • Canon 3200B002 | User Manual - Page 47
    full-screen display before scanning, scanned images are displayed at full size on the screen. Hint This is not usually practical for large scanners such as the DR7090C. ■ Using CapturePerfect 3.0 This section describes how to start CapturePerfect 3.0 and scan documents. The procedure for using the
  • Canon 3200B002 | User Manual - Page 48
    [Scan Batch to File Setting] dialog box opens. 7. Click [Scanner Setting]. The [Configure Device Settings] dialog box opens. IMPORTANT If [Canon DR-7090C] is not displayed in [Scanner Name], you must re-install the ISIS/TWAIN driver. 4. Set the [Default Page Size]. IMPORTANT If you select [Default
  • Canon 3200B002 | User Manual - Page 49
    , refer to the CapturePerfect 3.0 Operation Guide. • If a Feed Option other than [Standard Feeding] or [Manual Feeding] is selected, once you have started scanning, each document placed in the Document Feed Tray is scanned, and when no document is loaded, the scanner enters the standby state. • If
  • Canon 3200B002 | User Manual - Page 50
    11. When the [Continue Scanning] dialog box appears, verify that a document is loaded, and click either [Continue Scanning] or [Stop Scanning]. Hint If Use Continue Scanning dialog in the [Scan] menu is not checked, scanning finishes
  • Canon 3200B002 | User Manual - Page 51
    an application that supports CapturePerfect 3.0 or the PDF file format, and print the page image only at its original size. IMPORTANT • Print (at original size) PATCH T (A4) and PATCH II (A4) sheets on A4-size paper, or PATCH T (LTR) and PATCH II (LTR) on LTR paper. When the scanner recognizes this
  • Canon 3200B002 | User Manual - Page 52
    document that you want to save as a separate file before placing the documents on the scanner. Insert patchcode sheets in front of the documents pattern is detected, the patchcode sheet image is not saved and scanning continues. ] dialog box of the ISIS driver properties, select [Patchcode] from
  • Canon 3200B002 | User Manual - Page 53
    green. 4. Press the Stop key and display "Count Only Mode" on the display panel. Co u n t On l y Mo d e 00000 5. Place the document in the feeder, and press the Start key. The document is sent through the feeder, and the number of pages appears on the counter display area. 6. Press the Stop key
  • Canon 3200B002 | User Manual - Page 54
    from the document feeder tray and the document eject tray. 2. Open the feeder cover. Operate the opening lever, and then slowly raise the cover until it stops. 3. Confirm the location of the paper jam. 4. If the document is jammed under the feeder guide, grasp the tab inside the scanner to open
  • Canon 3200B002 | User Manual - Page 55
    5. Rotate the dial on your side of the scanner to remove any paper jammed inside the feeder. Chapter forward feeds jammed paper into the document eject tray. After feeding the paper, raise the document feeder tray and remove the paper. 6. Close the feeder guide. CAUTION Take care to avoid pinching
  • Canon 3200B002 | User Manual - Page 56
    supported by the feeder, or is the document paper of substandard quality? What to do: See "Documents" on p. 3-2 for information about required document properties. • What to check: Is a jam being caused by document paper that is not sliding properly? What to do: Scan such paper from the flatbed
  • Canon 3200B002 | User Manual - Page 57
    Chapter 4 User Modes 1. About the User Modes 4-2 User Mode Functions 4-2 How to Set the User Modes 4-3
  • Canon 3200B002 | User Manual - Page 58
    Modes You can configure the scanner settings with the user modes described below. User Mode Functions User mode functions are as follows: ■ Count Only Mode Co u n t On l y Mo d e ON [ OFF ] ON: Counts the number of pages in a document using stand-alone scanner operations. (See "Count Only Mode
  • Canon 3200B002 | User Manual - Page 59
    document pages fed by the scanner. How to Set the User Modes Use the following procedure to configure user mode settings. 1. Press Menu to display the user - b y Mo d e 240 60 [ 10 ] USB Sh o r t Pa c k e t [ ON ] OF F Japanese ON [ OFF ] SCS I Sp e e d [ 20 ] 10 5 D i sp l ay Con t r
  • Canon 3200B002 | User Manual - Page 60
    Chapter 5 Maintenance 1. Changing the Stamp Cartridge 5-2 2. Daily Cleaning 5-4 About the Cleaning Cloth and Cleaning Paper .....5-4 Cleaning the Main Unit 5-4 Cleaning the Flatbed (Platen Glass) and Pressure Board 5-5 Cleaning the Feeder 5-6 Cleaning the Power Plug 5-12
  • Canon 3200B002 | User Manual - Page 61
    documents, you should use the following procedure to replace the stamp cartridge whenever the stamp mark becomes smudged or faint. Contact your sales reprentative or service guide, and then open the inner cover. The feeder guide has a green tab, while the inner cover located under the feeder guide
  • Canon 3200B002 | User Manual - Page 62
    5. Close the feeder guide and inner cover. CAUTION Take care to avoid pinching your fingers when closing the feeder guide and inner cover. 6. Close the feeder cover. CAUTION Take care to avoid pinching your fingers when closing the feeder cover. 5-3 Chapter 5 Maintenance
  • Canon 3200B002 | User Manual - Page 63
    or water directly onto the flatbed (platen glass). Sprayed liquid can get inside the scanner and soil the light source and lens. • Overuse of water and allowing the scanner to become too wet during cleaning can damage scanned documents and cause malfunction of the scanner. About the Cleaning Cloth
  • Canon 3200B002 | User Manual - Page 64
    platen glass) or pressure board can cause soiling of scanned images, or document size detection errors. Clean the flatbed (platen glass) and pressure board periodically. 1. Open the feeder. Chapter 5 Maintenance 2. Wipe the flatbed (platen glass), scanning glass (narrow strip of glass) and pressure
  • Canon 3200B002 | User Manual - Page 65
    3. Slowly and carefully close the feeder. Chapter 5 Maintenance Cleaning the Feeder Without periodic cleaning, a problem may be caused on the scanned image or the document may become soiled. Clean the feeder periodically. 1. Open the feeder cover. Operate the opening lever, and then slowly raise
  • Canon 3200B002 | User Manual - Page 66
    3. Wipe the 13 rollers on the feeder guide with a cloth moistened with plain water and thoroughly wrung , dry cloth. 4. Grasp the tab in the front to open the feeder guide. 6. Wipe the four rollers inside the feeder guide with a cloth moistened with plain water and thoroughly wrung out. Next, wipe
  • Canon 3200B002 | User Manual - Page 67
    . 9. Open the feeder. Chapter 5 Maintenance CAUTION Take care to avoid pinching your fingers when closing the feeder guide. 8. Close the feeder cover. 10. Wipe the feeder roller (white) and platen roller (black) with a cloth moistened with plain water and thoroughly wrung out. Next, wipe the
  • Canon 3200B002 | User Manual - Page 68
    slowly while wiping it. Chapter 5 Maintenance 12. Remove the scanning area cleaning tool from inside the cover. Dial 11. Pull the lever on the upper part of the feeder to open the scanning area on the feeder. 13. Remove one sheet of cleaning paper from the plastic bag, and fold it
  • Canon 3200B002 | User Manual - Page 69
    platen roller, rotate the roller slowly while wiping it. 15. Open the inner cover. Platen Roller 17. Clean the feeder's scanning area along the rail. 5-10
  • Canon 3200B002 | User Manual - Page 70
    tool, and place the cleaning tool inside the cover. CAUTION Take care to avoid pinching your fingers when closing the cover. 21. Press the center part of the cover until it clicks into place. Make sure that the cover is completely closed. 5-11
  • Canon 3200B002 | User Manual - Page 71
    22. Slowly and carefully lower the feeder back down. Chapter 5 Maintenance Cleaning the Power Plug If you leave the power plug connected to the power outlet for a long period of time, dust may accumulate at the power outlet, and cause a fire or electrical shock. Clean the power plug periodically.
  • Canon 3200B002 | User Manual - Page 72
    Chapter 6 Practical Examples 1. Messages 6-2 Status Display 6-2 Error Messages 6-3 2. Troubleshooting 6-5 Trouble Categories 6-5 Problem and Solution 6-5 3. Uninstalling the Software 6-11 Uninstalling the ISIS/TWAIN Driver 6-11
  • Canon 3200B002 | User Manual - Page 73
    panel messages: "status indicator messages" and "error messages" that appear when the scanner encounters a problem. Status Display The following messages appear on the display panel to indicate the scanner's operating state: ■ Count Only Mode Co u n t On l y Mo d e 00000 Status: Operating in
  • Canon 3200B002 | User Manual - Page 74
    occurred while transferring image data for a Job function. Solution: Check the Job Registration Tool settings, and scan again. For details, see Chapter 9 "Job Registration Tool Settings" of the Software section. ■ Detect Mix Doc. De t ec t Mi x Doc . Jxxx Cause: Mixed size documents were detected
  • Canon 3200B002 | User Manual - Page 75
    : Exxxxxxx (any error code not listed above) Cause: Internal scanner error. Solution: Turn the power OFF, and restart the scanner. If this does not solve the problem, make a note of the error code and contact your Canon service representative. ■ Single-Pass OFF S i n g l e - Pa s s OFF Cause: This
  • Canon 3200B002 | User Manual - Page 76
    Panel Does Not Display Properly (See p. 6-10) • Job Functions Do Not Operate Properly (See p. 6-10) It you cannot resolve a problem, contact your local authorized Canon dealer or your service representative. Problem and Solution ■ The Scanner Does Not Turn ON If the scanner does not turn ON, first
  • Canon 3200B002 | User Manual - Page 77
    does not solve the problem, consider the following possible causes: Cause Solution The scanner does not support your USB interface. This product is not guaranteed to operate with all types of USB interfaces. Contact your local authorized Canon dealer or service representative for more information
  • Canon 3200B002 | User Manual - Page 78
    scanner's power switch turned ON? If this does not solve the problem, consider the following possible causes: Cause Solution The ISIS/TWAIN driver following: ✔ Is Single-Pass Duplex set to ON in the user mode settings? ✔ Is Long Document mode set to OFF? (See p. 4-2.) IMPORTANT Single-pass duplex
  • Canon 3200B002 | User Manual - Page 79
    Scanning Results Are Not as Expected If the scanned images do not appear as expected, one or more ISIS/TWAIN driver settings may be incorrect, or your application may not support certain scanner functions. Problem Cause Solution The scanned image is too dark (or faint). The [Brightness] setting is
  • Canon 3200B002 | User Manual - Page 80
    glass and rollers, the scanning glass inside the scanner may be scratched. Contact your local authorized Canon dealer or service representative. Chapter 6 Practical Examples Problem Cause Solution The scanned image is abnormal for certain documents. A detection function such as border removal is
  • Canon 3200B002 | User Manual - Page 81
    " of the Software section. Chapter 6 Practical Examples Problem Cause Solution The Job function does not operate after selecting the job and pressing the Start key. The Windows Events function is not configured properly. Configure the Windows Events function settings so that [DR-7090C Job Tool
  • Canon 3200B002 | User Manual - Page 82
    6 Practical Examples 3. Uninstalling the Software Some scanner malfunctions can be resolved by reinstalling the software. Before reinstalling the software, make sure to completely uninstall any previous installation first. Uninstalling the ISIS/TWAIN Driver The following procedure uses the ISIS
  • Canon 3200B002 | User Manual - Page 83
    The file-deletion confirmation screen appears. 4. Click [Yes] to proceed with uninstallation. 5. When uninstallation is finished, click [Finish]. Chapter 6 Practical Examples 6-12
  • Canon 3200B002 | User Manual - Page 84
    Chapter 7 Appendix 1. Specifications 7-2 Specifications for the Scanner 7-2 Options 7-3 Consumables 7-3 External Dimensions 7-4 2. Index 7-5
  • Canon 3200B002 | User Manual - Page 85
    Chapter 7 Appendix 1. Specifications Specifications for the Scanner Type Desktop ADF/flatbed scanner Document Size Width: 5.5" to 11.7" (139.7 mm to 298.1 mm) Length: 5.0" to 17.0" (128 mm to 431.8 mm) (Normal Mode) 5.0" to 24.8" (128 mm to 630 mm) (Long Document Mode) Document Thickness Black-and-
  • Canon 3200B002 | User Manual - Page 86
    software supports them. • They may not work depending on your computer's capabilities and the software you are using. Specifications are subject to change without notice. Options Stamp Unit Stamps a mark on the surface of a document or your service representative. 7-3 Chapter 7 Appendix
  • Canon 3200B002 | User Manual - Page 87
    External Dimensions Chapter 7 Appendix 23.7" (602 mm) (16.4" (714 mm)) 12.4" (314 mm) 5.9" (150 mm) 24.3" (618 mm) 12.5" (317 mm) 14.8" (377 mm) 23.1" (586 mm) 1.3" (32 mm) 7-4
  • Canon 3200B002 | User Manual - Page 88
    3-8 Flatbed 3-5 Flatbed (Platen Glass 1-11 H Handling 1-5 I Installation Location 1-2 Installation Requirements 2-3 J Job Function 3-11 Job Keys 1-13 Job Mode 3-12 Job Registration Tool 3-11 M Manuals for the Scanner iii Menu Key 1-12 Moving the Scanner 1-4 N Names and Functions of Parts
  • Canon 3200B002 | User Manual - Page 89
    1-11 R Read Manual 2-5 S Scanning area cleaning tool 1-11 SCSI Cards 2-3 SCSI Connection 2-7 SCSI Connectors 1-12 SCSI ID 2-7 Securing Braces 1-3, 1-11 Set Keys 1-12 Setup 2-2 Setup Menu 2-4 Single-Pass Duplex 4-3 Slide Guide 1-11 Software Installation 2-4 Specifications 7-2 Stamp
  • Canon 3200B002 | User Manual - Page 90
    User Manual Software Please read this manual before using the scanner. After you finish reading this manual, keep it in a safe place for future reference.
  • Canon 3200B002 | User Manual - Page 91
    Basic Condition Settings 10-2 Confirming Basic Conditions for Scanning ......... 10-2 2. Practical Examples 10-4 Scanning Documents of Unregistered Page Sizes 10-4 Specifying Scanning Area 10-5 Configuring Scanner Settings According to Purpose 10-5 Registering Your Settings 10-8 ii Software
  • Canon 3200B002 | User Manual - Page 92
    Chapter 8 ISIS/TWAIN Driver Settings 1. Before Use 8-2 2. ISIS/TWAIN Driver Settings Dialog Boxes....... 8-4 Basic Setup Dialog Box 8-5 Scan Area Dialog Box 8-9 Orientation Settings Dialog Box 8-11 Advanced Settings Dialog Box 8-12 Gamma Settings Dialog Box 8-15 Other Settings Dialog Box 8-16
  • Canon 3200B002 | User Manual - Page 93
    Driver Settings 1. Before Use An application program that supports the ISIS or TWAIN driver is required to use the DR-7090C. The DR-7090C requires that it be selected for use as a scanner. The supplied CapturePerfect 3.0 application uses the ISIS driver user's manual as needed to select the scanner
  • Canon 3200B002 | User Manual - Page 94
    ] menu. Chapter 8 ISIS/TWAIN Driver Settings 6. Click [Scanner Setting] in the [Scan] menu. The [Select Scanner] dialog box appears. 3. Select [Canon DR-7090C] ➔ click the [Settings] button. The settings dialog box for the ISIS driver appears. If [Canon DR-7090C] does not appear, try installing
  • Canon 3200B002 | User Manual - Page 95
    dialog box, Advanced Settings dialog box, and Other Settings dialog box. The contents of the settings dialog boxes depend on whether the ISIS or TWAIN driver is used. For details, see the description of each dialog box. Basic Setup Dialog Box (See p. 8-5) Advanced Settings Dialog Box (See p. 8-12
  • Canon 3200B002 | User Manual - Page 96
    for TWAIN-compatible application programs (Job Registration Tool). • The [Scanning Option] is a function for setting the TWAIN driver, so it does not appear with the ISIS driver. • When you use a TWAIN-compatible application program that scans from the settings dialog box, the [Scan] button
  • Canon 3200B002 | User Manual - Page 97
    box. User Preference Click [Save] to open the [Save User Preference] dialog box. The [Save User Preference] document. We recommend confirming an image by prescanning the first page. • When saving an image file in JPEG format, select [256-level Gray] or [24-bit Color]. Chapter 8 ISIS/TWAIN Driver
  • Canon 3200B002 | User Manual - Page 98
    programs do not support auto-page-size detection. Dots per inch Select the scanning resolution. Hint Higher resolutions provide clearer images, but produce larger files. Chapter 8 ISIS/TWAIN Driver Settings Brightness Adjust the brightness of images to be scanned. Hint • If images are too dark
  • Canon 3200B002 | User Manual - Page 99
    if non-blank pages are skipped, adjust the content density. Chapter 8 ISIS/TWAIN Driver Settings [Deskew] Check Box The Deskew function detects slanted document pages and straightens the scanned images. IMPORTANT The Deskew function does not work properly in the following situations. Disable Deskew
  • Canon 3200B002 | User Manual - Page 100
    scan settings dialog box of an application or in the Basic Setup dialog box of the scanner driver. This dialog box allows you to define the area of the document page to scan on a selected page size, and register non-standard document page sizes. The Scan Area dialog box is different for the ISIS
  • Canon 3200B002 | User Manual - Page 101
    a part inside the area window with the mouse. • With CapturePerfect, the last scanned image appears in the area window. Buttons [Preview] Button (TWAIN Driver Only) Load the document and then click the [Preview] button to scan one document page and display its preview image in the area window. 8-10
  • Canon 3200B002 | User Manual - Page 102
    Driver Settings Document Orientation Specify a rotation angle to correct the orientation of images. Hint • Scanned images are rotated as follows according to the orientation of loaded documents and the selected angle. Flatbed Document: Face Down Feeder Document: Face Up Document Orientation Image
  • Canon 3200B002 | User Manual - Page 103
    Version of Advanced Settings Dialog Box (ISIS Driver) This dialog box is displayed when the ISIS driver is accessed from a scanner setting or scanning dialog box belonging to an ISIS-compatible application program. It contains settings that are not supported in the settings dialog box belonging to
  • Canon 3200B002 | User Manual - Page 104
    Advanced Settings Dialog Box (TWAIN Driver) This dialog box is Flatbed Document: Face Down Feeder Document: Face Up Text Orientation Output Image Different Size Originals Set this item when scanning with [Single-Pass Dup.] set to [OFF] in the user mode of the scanner. If a mixture of documents
  • Canon 3200B002 | User Manual - Page 105
    If punch holes are located within text or graphics in the document, they may be misidentified as graphics, and may not be removed. [Reverse Image] Check Box (TWAIN Driver Only) Select this check box to output images scanned in black and white (binary) with black and white reversed. IMPORTANT
  • Canon 3200B002 | User Manual - Page 106
    box. This dialog box allows you to change the settings for the gamma correction value. Chapter 8 ISIS/TWAIN Driver Settings • The gamma correction value, gamma curve graph, and sample image color are interlinked. • Clicking a point in the gamma curve graph with your mouse changes the gamma curve
  • Canon 3200B002 | User Manual - Page 107
    the desired image data. Refer to "Gamma Table Files" in the ISIS/TWAIN driver Help for document loaded in the feeder or on the flatbed is scanned. After that, you can continue scanning documents by loading a new document in the feeder or on the flatbed and then pressing the Start key on the scanner
  • Canon 3200B002 | User Manual - Page 108
    Driver Settings [Automatic Feeding] Once scanning is started from an application program, whenever a document is loaded in the feeder, the scanner automatically detects it and begins scanning. To finish scanning, press the stop button on the scanner Side] is set to [Flatbed], [Automatic Feeding] is
  • Canon 3200B002 | User Manual - Page 109
    . Chapter 8 ISIS/TWAIN Driver Settings Prescan Prescan and display the first document page in the Prescan window when scanning is started. image in the Prescan window. Hint [Patchcode Orientation] must be set as follows to match that in the document. Flatbed Document: Face Down Feeder Document
  • Canon 3200B002 | User Manual - Page 110
    Chapter 9 Job Registration Tool Settings 1. Before Use 9-2 Job Function 9-2 Starting Job Registration Tool 9-2 2. Job Registration Tool 9-3 3. Settings Dialog Boxes 9-4 [New/Editing] Dialog Box 9-4 [Admin] Dialog Box 9-9
  • Canon 3200B002 | User Manual - Page 111
    The scanning conditions, file format of the image data to be saved, and save destination are registered to a job, and the image data scanned with the job function is processed Tool. 1. From the Windows task bar, click [Start] ➔ click [All Programs] ➔ [Canon DR-7090C] ➔ [Job Registration Tool]. 9-2
  • Canon 3200B002 | User Manual - Page 112
    Job Registration Tool Job Registration Tool consists of the main window below and the [New/Editing] and [Admin] dialog ] Menu Open the [Admin] dialog box to configure settings for monitoring the storage folder for images and backing up job data. (See "[Admin] Dialog Box" on p. 9-9.) [Help] Menu
  • Canon 3200B002 | User Manual - Page 113
    will vary as follows. Save as file Allows you to save scanned images on a specified computer. Send by E-Mail Allows you to send scanned images as e-mail attachments. Print Allows you to print scanned images on a specified printer. Launcher Allows you to start applications specified in the
  • Canon 3200B002 | User Manual - Page 114
    E-Mail Launcher No. ✔ ✔ ✔ ✔ Job title ✔ ✔ ✔ ✔ Scanner setting ✔ ✔ ✔ ✔ Mail address - - ✔ - Save image - - ✔ - Save to My Pictures folder ✔ - ✔ - Save are those specified in the Windows "Events" function settings. (See "Setting the Events Function" on p. 3-13
  • Canon 3200B002 | User Manual - Page 115
    ] Enter the text message for sent mail. When multi-page documents are scanned, image files are created as follows in accordance with the file format. PDF: All pages are saved in a single image file. BMP: Each page is saved in a separate image file. TIFF: You can select the method for saving when
  • Canon 3200B002 | User Manual - Page 116
    [Fit to paper] to scale images to fit the printed paper. ■ Settings of [PDF setting] Dialog Box You can configure the following settings in the [PDF setting] dialog box. Multi-PDF settings Select the method for saving PDF files when scanning multi-page documents. Hint • Select [Single page] to
  • Canon 3200B002 | User Manual - Page 117
    in the list box. Characters within document images are recognized as text and saved as appended text data in PDF (*pdf) files. ■ Settings of [TIFF Hint If your application program does not support the above compression formats, you may be unable to open scanned image files. In this case, disable [
  • Canon 3200B002 | User Manual - Page 118
    job data. Chapter 9 Job Registration Tool Settings ■ Capacity Warning Settings The capacity warning settings allow you to specify in advance the folder for saving image files, and the space to be available for saving files. If the space required to save a file will exceed the specified warning size
  • Canon 3200B002 | User Manual - Page 119
    image size reaches the specified maximum, a message appears and scanning stops. IMPORTANT • Contact your mail server administrator if you are uncertain about any mail server settings. • Choose a maximum attachment file size that does not exceed the corresponding setting on your mail server. 9-10
  • Canon 3200B002 | User Manual - Page 120
    to back up the registered jobs when the same job is to be executed in a different environment, such as occurs when multiple users log on to Windows or when multiple scanners are used. [Back Up] Button Write a backup file (*.reg) of registered job data to any folder. Chapter 9 Job Registration Tool
  • Canon 3200B002 | User Manual - Page 121
    Examples 1. About Basic Condition Settings 10-2 Confirming Basic Conditions for Scanning..........10-2 2. Practical Examples 10-4 Scanning Documents of Unregistered Page Sizes 10-4 Specifying Scanning Area 10-5 Configuring Scanner Settings According to Purpose 10-5 Registering Your Settings
  • Canon 3200B002 | User Manual - Page 122
    the scanner settings. For details on settings, see Chapter 8 "ISIS/TWAIN Driver Settings". Confirming Basic Conditions for Scanning When you scan a document, make ] is selected, the edges of the document are detected and images that match the size of the document are saved. Dots per inch Select the
  • Canon 3200B002 | User Manual - Page 123
    side is set to [Auto], documents placed in the feeder tray will be scanned. If there are no documents in the feeder tray, the flatbed will be scanned. • If the scanning side is set to [Skip Blank Page], the images of blank pages are deleted when the images are saved. Chapter 10 Practical Examples
  • Canon 3200B002 | User Manual - Page 124
    Chapter 10 Practical Examples 2. Practical Examples This section provides an overview of the basic setting items that are the minimum requirements when configuring the scanner settings. For details on settings, see Chapter 8 "ISIS/TWAIN Driver Settings". Scanning Documents of Unregistered Page
  • Canon 3200B002 | User Manual - Page 125
    dialog box. (See p. 8-9.) • With CapturePerfect 3.0, the last scanned image appears in the preview window. Scan the document you want to set the area of with [Scan Single Page] in order to display the image in the preview window. Configuring Scanner Settings According to Purpose Set the scanning
  • Canon 3200B002 | User Manual - Page 126
    in [Color drop-out] in the Advanced Settings dialog box, and that color will be enhanced. Chapter 10 Practical Examples ■ When you want to reverse the black and white in scanned images (TWAIN driver only) Select the [Reverse Image] check box in the Advanced Settings dialog box. This outputs scanned
  • Canon 3200B002 | User Manual - Page 127
    dialog box. (See p. 8-13.) Chapter 10 Practical Examples The text orientation on each page is detected, and the scanned image is rotated in 90-degree increments to correct the orientation. Flatbed Document: Face Down Feeder Document: Face Up Text Orientation Output Image Hint When [Text Orientation
  • Canon 3200B002 | User Manual - Page 128
    10 Practical Examples Hint Images are rotated as follows according to the orientation of the loaded document and the selected angle. Flatbed Document: Face Down Feeder Document: Face Up Document Orientation Image Rotation (Clockwise) 0 degrees 90 degrees 180 degrees 270 degrees Output Image User
  • Canon 3200B002 | User Manual - Page 129
    PTY. LTD. 1 THOMAS HOLT DRIVE, NORTH RYDE, SYDNEY. N.S.W, 2113. AUSTRALIA CANON SINGAPORE PTE. LTD. 1 HARBOUR FRONT AVENUE #04-01, KEPPEL BAY TOWER, SINGAPORE 098632 CANON HONGKONG COMPANY LTD. 19TH FLOOR, THE METROPOLIS TOWER, 10 METROPOLIS DRIVE, HUNGHOM, KOWLOON, HONG KONG. PUB. CE-IE-667-04
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
Please read this manual before using the scanner.
After you finish reading this manual, keep it in a safe place
for future reference.
User Manual