Canon BJ-20 User Manual - Page 70

Set Form Length, Select/Cancel Emphasized Mode, Set Print Mode

Get Canon BJ-20 PDF manuals and user guides View all Canon BJ-20 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 70 highlights

fed in n/60 inch. z If the DIP switch 7 is set to OFF (AGM mode disabled), paper is fed in n/72 inch. z After text line spacing is set, use the ESC 2 code to enable the text line spacing. Set Form Length Set form (page) length to n lines or inches, where n can range from 1 to 255. FORMAT DEC HEX In Lines ESC C n 27 67 n 1B 43 n In Inches ESC C 0 n 27 67 0 n 1B 43 00 n Comment z The current line position becomes the top of page position. z Later changes in line spacing have no effect on page length. z This code releases the skip perforation settings, but does not change the vertical tab settings. z If the printer is in IBM Proprinter X24E emulation with the auto sheet feeder installed, page length setting becomes effective after the current page is ejected. The exceptions are: if the current page is at the top of page position, or if the present line number is smaller than the page length setting, then the page is not ejected, and the current line position taken as the top of page. z If the printer is in the Canon BJ-130e emulation, then regardless of the auto sheet feeder, the new page length setting becomes effective immediately, and the current position is taken as the top of page. Select/Cancel Emphasized Mode Select or cancel printing in twice the normal dot density. FORMAT DEC HEX Select ESC E 27 69 1B 45 Cancel ESC F 27 70 1B 46 Comment This mode overrides the condensed (17 cpi) mode. When the ESC E is entered in 17 cpi mode, the printer is set to the emphasized 10 cpi mode. Set Print Mode

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
fed in n/60 inch.
If the DIP switch 7 is set to OFF (AGM mode disabled), paper is
fed in n/72
inch.
After text line spacing is set, use the ESC 2 code to enable the
text line spacing.
Set form (page) length to n lines or inches, where n can range from 1 to
255.
Comment
The current line position becomes the top of page position.
Later changes in line spacing have no effect on page length.
This code releases the skip perforation settings, but does not
change the vertical tab settings.
If the printer is in IBM Proprinter X24E emulation with the auto
sheet feeder installed, page length setting becomes effective after
the current page is ejected. The exceptions are: if the current page
is at the top of page position, or if the present line number is
smaller than the page length setting, then the page is not ejected,
and the current line position taken as the top of page.
If the printer is in the Canon BJ-130e emulation, then regardless
of the auto sheet feeder, the new page length setting becomes
effective immediately, and the current position is taken as the top
of page.
Select or cancel printing in twice the normal dot density.
Comment
This mode overrides the condensed (17 cpi) mode. When the ESC E is
entered in 17 cpi mode, the printer is set to the emphasized 10 cpi mode.
Set Form Length
In Lines
In Inches
FORMAT
ESC C n
ESC C 0 n
DEC
27 67 n
27 67 0 n
HEX
1B 43 n
1B 43 00 n
Select/Cancel Emphasized Mode
Select
Cancel
FORMAT
ESC E
ESC F
DEC
27 69
27 70
HEX
1B 45
1B 46
Set Print Mode