Canon MP190 Quick Start Guide - Page 50

LED Cannot Be Seen At All, Power Lamp Flashes Green and Alarm Lamp Flashes Orange, Alternately - service mode

Get Canon MP190 - PIXMA Color Inkjet PDF manuals and user guides
UPC - 013803095166
View all Canon MP190 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

„ Power Lamp Flashes Green and Alarm Lamp Flashes Orange Alternately The Power and Alarm lamps flash alternately as shown below. Disconnect the USB cable from the machine, turn the machine off, then unplug the machine from the power supply. Plug the machine back in and turn the machine back on. If the problem is not resolved, contact your Canon Service representative. Error Code Cause E, 2, 2 The FINE Cartridge Holder does not move. E, 2, x E, 3, x E, 4, x An error requiring servicing might have occurred. Action Cancel printing, turn off the machine, then remove the protective material from the FINE Cartridge Holder or paper jam that is preventing the FINE Cartridge Holder from moving. Caution Be careful not to touch the components inside the machine. The machine may not print out properly if you touch it. Turn off the machine, and unplug the power plug of the machine from the power supply. Then, plug the power plug of the machine back in, and turn on the machine again. If the same error occurs, contact your Canon Service representative. LED Cannot Be Seen At All Cause The machine is not powered on or the LED is in the screen-saver mode. Action z If the Power lamp is off The machine is not powered on. Connect the power plug and press the ON button. The machine will power on and the LED will light. z If the Power lamp is lit The LED may be in the screen-saver mode. On the Operation Panel, press a button other than the ON button. 46 Troubleshooting

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
46
Troubleshooting
Power Lamp Flashes Green and Alarm Lamp Flashes Orange
Alternately
The
Power
and
Alarm
lamps flash alternately as shown below.
Disconnect the USB cable from the machine, turn the machine off, then unplug the machine from
the power supply. Plug the machine back in and turn the machine back on.
If the problem is not resolved, contact your Canon Service representative.
LED Cannot Be Seen At All
Error Code
Cause
Action
E, 2, 2
The FINE Cartridge
Holder does not move.
Cancel printing, turn off the machine, then remove the protective material
from the FINE Cartridge Holder or paper jam that is preventing the FINE
Cartridge Holder from moving.
Caution
Be careful not to touch the components inside the machine. The machine
may not print out properly if you touch it.
E, 2, x
E, 3, x
E, 4, x
An error requiring
servicing might have
occurred.
Turn off the machine, and unplug the power plug of the machine from the
power supply. Then, plug the power plug of the machine back in, and turn
on the machine again. If the same error occurs, contact your Canon
Service representative.
Cause
Action
The machine is not powered on or the
LED is in the screen-saver mode.
If the
Power
lamp is off
The machine is not powered on. Connect the power plug and press the
ON
button. The machine will power on and the LED will light.
If the
Power
lamp is lit
The LED may be in the screen-saver mode. On the Operation Panel, press a
button other than the
ON
button.