Compaq Presario CQ56-100 Compaq Presario CQ56 Notebook PC and HP G56 Notebook - Page 75

Remove the two Phillips 2.5×4.0, Remove the following cables from the system board

Get Compaq Presario CQ56-100 - Notebook PC PDF manuals and user guides View all Compaq Presario CQ56-100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 75 highlights

Remove the following cables from the system board: ● Power connector cable (see Power connector on page 58) ● USB board cable (see USB board on page 56) 1. Position the computer upright with the right side toward you. 2. To remove the optical drive cable, disconnect it from the system board (1), and then remove the two Phillips 2.0×6.0 screws (2) that secure the optical drive cable to the computer. 3. Lift the optical drive cable straight up (3) to remove it. 4. Remove the two Phillips 2.5×4.0 (1) screws that secure the system board to the computer. 5. Lift the right edge (2) of the system board. Component replacement procedures 67

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
Remove the following cables from the system board:
●
Power connector cable (see
Power connector
on page
58
)
●
USB board cable (see
USB board
on page
56
)
1.
Position the computer upright with the right side toward you.
2.
To remove the optical drive cable, disconnect it from the system board
(1)
, and then remove the
two Phillips 2.0×6.0 screws
(2)
that secure the optical drive cable to the computer.
3.
Lift the optical drive cable straight up
(3)
to remove it.
4.
Remove the two Phillips 2.5×4.0
(1)
screws that secure the system board to the computer.
5.
Lift the right edge
(2)
of the system board.
Component replacement procedures
67