D-Link DAP-2590 Product Manual - Page 78

Troubleshooting - problem

Get D-Link DAP-2590 - AirPremier N Dual Band PoE Access Point PDF manuals and user guides
UPC - 790069316043
View all D-Link DAP-2590 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 78 highlights

Section 5 - Troubleshooting Troubleshooting This chapter provides solutions to problems that can occur during the installation and operation of the DAP-2590 Wireless Access Point. We will cover various aspects of the network setup, especially the network adapters. Please read the following if you are having any technical difficulties. Note: It is recommended that you use an Ethernet connection to configure the DAP-2590. 1. The computer used to configure the DAP-2590 cannot access the Configuration menu. • Check if the LAN LED on the DAP-2590 is ON. If the LED is not ON, check if the cable for the Ethernet connection is securely inserted. • Check if the Ethernet adapter is working properly. Please see item 3 of this Troubleshooting section to check that the drivers for the network adapters are loaded properly. • Check if the IP address is in the same range and subnet as the DAP-2590. Note: The default IP address of the DAP-2590 is 192.168.0.50. All the computers on the network must have a unique IP address in the same range, e.g. 192.168.0.x. Any computers that have identical IP addresses will not be visible on the network. They must all have the same subnet mask, e.g. 255.255.255.0. • Do a Ping test to make sure that the DAP-2590 is responding. Go to Start>Run>Type "Command" and at the DOS prompt, type "ping 192.168.0.50". A successful ping will show four replies. Note: If you have changed the default IP address, make sure to ping the correct IP address assigned to the DAP-2590. D-Link DAP-2590 User Manual 78

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
µ¶
D-Link DAP-±590 User Manual
Section 5 - Troubleshooting
Troubleshooting
This chapter provides solutions to problems that can occur during the installation and operation of the DAP-2590 Wireless Access Point. We
will cover various aspects of the network setup, especially the network adapters. Please read the following if you are having any technical
difficulties.
Note:
It is recommended that you use an Ethernet connection to configure the DAP-2590.
1. The computer used to configure the DAP-2590 cannot access the Configuration menu.
•
Check if the LAN LED on the DAP-2590 is ON. If the LED is not ON, check if the cable for the Ethernet connection is securely
inserted.
•
Check if the Ethernet adapter is working properly. Please see item 3 of this Troubleshooting section to check that the drivers for the
network adapters are loaded properly.
•
Check if the IP address is in the same range and subnet as the DAP-2590.
Note:
The default IP address of the DAP-2590 is 192.168.0.50. All the computers on the network must have a unique IP address in the
same range, e.g. 192.168.0.x. Any computers that have identical IP addresses will not be visible on the network. They must all have the
same subnet mask, e.g. 255.255.255.0.
•
Do a Ping test to make sure that the DAP-2590 is responding. �o to
Start>Run
>Type
“Command” and at the DOS prompt, type “ping
192.168.0.50”. A successful ping will show four replies.
Note:
If you have changed the default IP address, make sure to ping the correct IP address assigned to the DAP-2590.