D-Link DCS-1000W User Manual - Page 8

Rear Panel - reset

Get D-Link DCS-1000W PDF manuals and user guides View all D-Link DCS-1000W manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

Rear Panel Antenna Connector Ethernet Cable Connector Slide Switch Antenna Connector Reset Button DC Power Connector I/O Connector Network Cable Connector The DCS-1000W's rear panel features an RJ-45 connector for connections to 10Base-T Ethernet cabling or 100Base-TX Fast Ethernet cabling (which should be Category 5 twisted-pair cable). The port supports the NWay protocol, allowing DCS-1000W to automatically detect or negotiate the transmission speed of the network. DC Power Connector The DC power input connector is located on the DCS-1000W's rear panel and is labeled DC 5V with a single jack socket to supply power to DCS-1000W. Reset Button Reset will be initiated when the reset button is pressed once and Power LED begins to flash. Factory Reset will be initiated when the reset button is pressed continuously for three seconds or when Power LED begins to light up. Release the reset button and the Power LED will begin to flash indicating that the DCS1000W's settings are reverting back to the factory settings. When factory reset is completed DCS-1000W will be set to default on channel 11 and EES-ID is set as "NULL String" (This default setting will let DCS-1000W connect to ANY access point on the infrastructure network). The IP address will also return to the default setting as 192.168.0.20. 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
7
Ethernet Cable
Connector
DC Power
Connector
I/O Connector
Antenna Connector
Slide Switch
Reset Button
Antenna Connector
Rear Panel
Network Cable Connector
The DCS-1000W’s rear panel features an RJ-45 connector for connections to
10Base-T Ethernet cabling or 100Base-TX Fast Ethernet cabling (which
should be Category 5 twisted-pair cable). The port supports the NWay
protocol, allowing DCS-1000W to automatically detect or negotiate the
transmission speed of the network.
DC Power Connector
The DC power input connector is located on the DCS-1000W’s rear panel and
is labeled
DC 5V
with a single jack socket to supply power to DCS-1000W.
Reset Button
Reset will be initiated when the reset button is pressed once and Power LED
begins to flash.
Factory Reset will be initiated when the reset button is pressed continuously
for three seconds or when Power LED begins to light up. Release the reset
button and the Power LED will begin to flash indicating that the DCS-
1000W’s settings are reverting back to the factory settings. When factory reset
is completed DCS-1000W will be set to default on channel 11 and EES-ID is
set as “NULL String” (This default setting will let DCS-1000W connect to
ANY access point on the infrastructure network). The IP address will also
return to the default setting as 192.168.0.20.