D-Link DCS-2100G Product Manual - Page 64

Reset Output, Trigger Condition

Get D-Link DCS-2100G - SECURICAM Network Camera PDF manuals and user guides
UPC - 790069274008
View all D-Link DCS-2100G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

DCS-2100G User's Manual All the time except for the above schedule: Delay second(s) before detecting next event: Take snapshots at second(s) after event: Trigger Condition: Reset Output: Trigger Action: Snapshot every second(s): Send snapshots by email: D-Link Systems, Inc. Using the DCS-2100G with an Internet Browser If you do not wish to set a schedule, this box must be checked. Sets the time delay before restarting to check the trigger condition when the current condition is triggered. After a snapshot is taken because of a trigger, another snapshot will be taken after the configured time in seconds. There are 4 conditions related to the digital input and three windows for motion detection. There can be multiple selections. Select the appropriate digital input condition according to the characteristics of the external device. High or low indicate external voltage input for level trigger, while rising or falling is for edge triggers. There are three windows shown for the names you defined for motion detection. Undefined will show instead of the window title if motion detection is not setup yet. An active, named motion window must be checked for motion detection to be possible. Check and save this option to reset the external device at the digital output back to the original state. There are four options for two actions regarding either trigger condition. They can have multiple selections. While choosing the trigger output alarm, the digital output will short both pins to connect the circuit of the attached external device; otherwise both pins will be open. While choosing to upload snapshots, the method can be either email or FTP. The snapshot names will be "videopre.jpg", videotrg.jpg", and "videopos.jpg" respectively for the snapshots before event, right upon event, and after event. The date and time suffix may be added according to the option. Confirm the external mail or FTP server settings in network configuration. The camera will send snapshots at the specified interval to the external server according to the chosen method. Remember this operation is dependent to the weekly schedule. Any upload action specified in the options above will use the method chosen here. The captured snapshot named "video.jpg" will be attached in the email with subject "Periodic snapshots." 64

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
64
DCS-2100G User’s Manual
D-Link Systems, Inc.
Using the DCS-2100G with an Internet Browser
All the time except
for the above
schedule:
If you do not wish to set a schedule, this box must be checked.
Sets the time delay before restarting to check the trigger
condition when the current condition is triggered.
After a snapshot is taken because of a trigger, another snapshot
will be taken after the configured time in seconds.
There are 4 conditions related to the digital input and three
windows for motion detection. There can be multiple selections.
Select the appropriate digital input condition according to the
characteristics of the external device.
High
or
low
indicate
external voltage input for level trigger, while
rising
or
falling
is
for edge triggers. There are three windows shown for the names
you defined for
motion detection.
Undefined
will show instead
of the window title if motion detection is not setup yet. An active,
named motion window must be checked for motion detection
to be possible.
Check and save this option to reset the external device at the
digital output back to the original state.
There are four options for two actions regarding
either trigger
condition. They can have multiple selections. While choosing
the trigger output alarm, the digital output will short both pins to
connect the circuit of the attached external device; otherwise
both pins will be open. While choosing to upload snapshots,
the method can be either email or FTP. The snapshot names
will be “videopre.jpg”, videotrg.jpg”, and “videopos.jpg”
respectively for the snapshots before event, right upon event,
and after event. The date and time suffix may be added
according to the option. Confirm the external mail or FTP server
settings in network configuration.
The camera
will send snapshots at the specified interval to the
external server according to the chosen method. Remember
this operation is dependent to the weekly schedule.
Any upload action specified in the options above will use the
method chosen here. The captured snapshot named “video.jpg”
will be attached in the email with subject “Periodic snapshots.”
Delay second(s)
before detecting
next event:
Take snapshots
at second(s) after
event:
Trigger Condition:
Reset Output:
Trigger Action:
Snapshot every
second(s):
Send snapshots by
email: