D-Link DSN-656 User Manual - Page 55

Entity and iSCSI Settings, iSNS IP Address

Get D-Link DSN-656 PDF manuals and user guides View all D-Link DSN-656 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

D-Link Document - User Manual CAUTION: VLAN ID, jumbo frames for both the switching hub and HBA on host must be enabled. Otherwise, the LAN connection cannot work properly.  ▼  Ping host: It can verify the port connection from a target to the corresponding host data port. Input the host's IP address and click the Start button. The system will display the ping result. Or click the Stop button to stop the test.  ▼  Reset Port: If the behavior of the port is abnormal, try to reset the port to make it normal. Entity and iSCSI Settings The Entity and iSCSI Settings tab is used to view the entity name of the system, and setup iSNS IP for the iSNS (Internet Storage Name Service) protocol. It allows automated discovery, management and configuration of iSCSI devices on a TCP/IP network. To use iSNS, an iSNS server needs to be added to the SAN. When this is done, the iSNS server IP address must be added to the storage system for iSCSI initiator service to send queries to it. To make changes, enter the Entity Name and the iSNS IP Address, and then click Apply. Copyright@2014 D-Link System, Inc. All Rights Reserved. 55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
D-Link Document – User Manual
CAUTION:
VLAN ID, jumbo frames for both the switching hub and HBA on host must be
enabled. Otherwise, the LAN connection cannot work properly.
▼
Ping host:
It can verify the port connection from a target to the corresponding host
data port. Input the host’s IP address and click the
Start
button. The system will display the
ping result. Or click the
Stop
button to stop the test.
▼
Reset Port:
If the behavior of the port is abnormal, try to reset the port to make it
normal.
Entity and iSCSI Settings
The
Entity and iSCSI Settings
tab is used to view the entity name of the system, and setup iSNS IP for the iSNS
(Internet Storage Name Service) protocol. It allows automated discovery, management and configuration of iSCSI
devices on a TCP/IP network. To use iSNS, an iSNS server needs to be added to the SAN. When this is done, the iSNS
server IP address must be added to the storage system for iSCSI initiator service to send queries to it.
To make changes, enter the
Entity Name
and the
iSNS IP Address
, and then click
Apply
.
55
Copyright@2014 D-Link System, Inc. All Rights Reserved.