Dell Alienware x15 R2 Service Manual - Page 16

Removing the battery, battery is disconnected, when the battery is fully discharged

Get Dell Alienware x15 R2 PDF manuals and user guides View all Dell Alienware x15 R2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

● If the battery gets stuck inside your computer as a result of swelling, do not try to release it as puncturing, bending, or crushing a lithium-ion battery can be dangerous. In such an instance, contact Dell technical support for assistance. See www.dell.com/contactdell. ● Always purchase genuine batteries from www.dell.com or authorized Dell partners and resellers. ● Swollen batteries should not be used and should be replaced and disposed properly. For guidelines on how to handle and replace swollen Lithium-ion batteries, see Handling swollen Lithium-ion batteries. Removing the battery Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the base cover. About this task CAUTION: This computer is designed without an RTC coin cell-battery. After a service incident where the computer battery is disconnected, when the battery is fully discharged, or when the computer is reassembled and turned on, an RTC reset cycle will occur. When an RTC Reset cycle occurs, the computer turns on and off three times. An "Invalid Configuration" error message is displayed prompting you to enter the BIOS and configure the date and time. The computer starts functioning normally after setting the date and time. CAUTION: Removing the battery resets the BIOS setup program's settings to default. It is recommended that you note the BIOS setup program's settings before removing the battery. The following image(s) indicate the location of the battery and provides a visual representation of the removal procedure. Steps 1. Disconnect the battery cable from the system board and remove the battery cable from the routing guides on the fan (applicable only if not disconnected earlier). 2. Remove the four screws (M2x4) that secure the battery to the palm-rest and keyboard assembly. 3. Lift the battery off the palm-rest and keyboard assembly. 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
●
If the battery gets stuck inside your computer as a result of swelling, do not try to release it as puncturing, bending, or
crushing a lithium-ion battery can be dangerous. In such an instance, contact Dell technical support for assistance. See
www.dell.com/contactdell
.
●
Always purchase genuine batteries from
www.dell.com
or authorized Dell partners and resellers.
●
Swollen batteries should not be used and should be replaced and disposed properly. For guidelines on how to handle
and replace swollen Lithium-ion batteries, see
Handling swollen Lithium-ion batteries
.
Removing the battery
Prerequisites
1.
Follow the procedure in
Before working inside your computer
.
2.
Remove the
base cover
.
About this task
CAUTION: This computer is designed without an RTC coin cell-battery. After a service incident where the computer
battery is disconnected, when the battery is fully discharged, or when the computer is reassembled and turned on, an
RTC reset cycle will occur. When an RTC Reset cycle occurs, the computer turns on and off three times. An "Invalid
Configuration" error message is displayed prompting you to enter the BIOS and configure the date and time. The computer
starts functioning normally after setting the date and time.
CAUTION: Removing the battery resets the BIOS setup program’s settings to default. It is recommended that you note the
BIOS setup program’s settings before removing the battery.
The following image(s) indicate the location of the battery and provides a visual representation of the removal procedure.
Steps
1.
Disconnect the battery cable from the system board and remove the battery cable from the routing guides on the fan (applicable
only if not disconnected earlier).
2.
Remove the four screws (M2x4) that secure the battery to the palm-rest and keyboard assembly.
3.
Lift the battery off the palm-rest and keyboard assembly.
16