Dell Alienware x17 R2 Service Manual - Page 44

Installing the display assembly, Steps, Prerequisites, About this task

Get Dell Alienware x17 R2 PDF manuals and user guides View all Dell Alienware x17 R2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

Steps 1. Remove the two screws (M2.5x5) that secure the left-display hinge to the palm-rest and keyboard assembly. 2. Peel the tape that secures the camera-cable connector latch to the system board. 3. Lift the latch and disconnect the camera cable from the system board. 4. Peel the tapes that secure the power-adapter port cable to the system board. 5. Lift the power-adapter port cable off the display-cable connector on the system board. 6. Peel the tape that secures the display-cable connector latch to the system board. 7. Lift the latch and disconnect the display-cable connector from the system board. 8. Remove the two screws (M2.5x5) that secure the power-adapter port-bracket to the palm-rest and keyboard assembly. 9. Turn the computer over. 10. Remove the display cable from the routing guide on the palm-rest and keyboard assembly. 11. Remove the Tobii-eye cable from the routing guide on the palm-rest and keyboard assembly. 12. Remove the four screws (M2.5x5) that secure the display assembly to the palm-rest and keyboard assembly. 13. Lift the display assembly off the palm-rest and keyboard assembly. Installing the display assembly Prerequisites If you are replacing a component, remove the existing component before performing the installation process. About this task CAUTION: Place the display assembly on a clean and flat surface to avoid damaging the display assembly. NOTE: The display assembly is a Hinge-Up Display (HUD) and cannot be further disassembled. If components within the display assembly must be replaced, the entire display assembly is to be replaced. 44

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
Steps
1.
Remove the two screws (M2.5x5) that secure the left-display hinge to the palm-rest and keyboard assembly.
2.
Peel the tape that secures the camera-cable connector latch to the system board.
3.
Lift the latch and disconnect the camera cable from the system board.
4.
Peel the tapes that secure the power-adapter port cable to the system board.
5.
Lift the power-adapter port cable off the display-cable connector on the system board.
6.
Peel the tape that secures the display-cable connector latch to the system board.
7.
Lift the latch and disconnect the display-cable connector from the system board.
8.
Remove the two screws (M2.5x5) that secure the power-adapter port-bracket to the palm-rest and keyboard assembly.
9.
Turn the computer over.
10.
Remove the display cable from the routing guide on the palm-rest and keyboard assembly.
11.
Remove the Tobii-eye cable from the routing guide on the palm-rest and keyboard assembly.
12.
Remove the four screws (M2.5x5) that secure the display assembly to the palm-rest and keyboard assembly.
13.
Lift the display assembly off the palm-rest and keyboard assembly.
Installing the display assembly
Prerequisites
If you are replacing a component, remove the existing component before performing the installation process.
About this task
CAUTION: Place the display assembly on a clean and flat surface to avoid damaging the display assembly.
NOTE:
The display assembly is a Hinge-Up Display (HUD) and cannot be further disassembled. If components within the display
assembly must be replaced, the entire display assembly is to be replaced.
44