Fujitsu MAF3364LC Manual/User Guide - Page 33

Environmental specifications, Table 2.2, Environmental/power requirements

Get Fujitsu MAF3364LC - Enterprise 36.4 GB Hard Drive PDF manuals and user guides View all Fujitsu MAF3364LC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

2.1.3 Environmental specifications Table 2.2 lists environmental and power requirements. Table 2.2 Environmental/power requirements Temperature (*1) Relative humidity Vibration (*2) Shock (*2) Altitute (above sea level) Power requirements Input power (*5) MAE3182 series MAE3091 series MAF3364 series MAG3182 series MAG3091 series Operating 5 to 50°C Non-operating -40 to 60°C DE surface temperature atoperating 5 to 55°C Gradient 15°C/h or less Operating 20 to 80%RH Non operating 20 to 80%RH Packaged (inside of a week) 5 to 90%RH Maximum wet bulb temperature 29°C (no condensation) Operating (*3) 0.3 mm (5 to 20Hz)/0.5G (20 to 250 Hz) or less Non-operating (*4) 3.1 mm (5 to 20Hz)/5G (20 to 250Hz) or less Packaged 3.1 mm (5 to 20Hz)/5G (20 to 250Hz) or less Operating 20G (2 ms) Non-operating 175G (2 ms) Operating -60 m to 3,000 m Non-operating -60 m to 12,000 m +12 VDC ±5% Ready (Average) 0.4 A 0.25 A 0.9 A 0.65 A Peak within 100 µs at spin-up 3.0 A 3.2 A 3.0 A Random W/R (about 80 IOPS) 0.8 A 0.7 A 1.3 A 1.0 A +5 VDC ±5% (*6) Ready 0.6 A 0.8 A 0.7 A Random W/R (about 80 IOPS) 6.8 A 1.0 A 0.9 A Ripple (*7) +5 V 250 mVp-p, +12 V 250 mVp-p (*1) For detail condition, see Section 4.1. (*2) Vibration applied to the drive is measured at near the mounting screw hole on the frame as much as possible. (*3) At random seek write/read and default on retry setting with log sweep vibration. (*4) At power-off state after installation Vibration displacement should be less than 2.5 mm. (*5) Input voltages are specified at the connector. (*6) The terminator power pin (SCSI connector) which supplies power to other terminators is not used (See Section 4.3). (*7) High frequency noise is less than 100 mVp-p. 2 - 4 C141-E064-03EN

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
C141-E064-03EN
2 - 4
2.1.3
Environmental specifications
Table 2.2 lists environmental and power requirements.
Table 2.2
Environmental/power requirements
MAE3182 series
MAE3091 series
MAF3364 series
MAG3182 series
MAG3091 series
Operating
5 to 50°C
Non-operating
–40 to 60°C
DE surface temperature atoperating
5 to 55°C
Gradient
15°C/h or less
Operating
20 to 80%RH
Non operating
20 to 80%RH
Packaged
(inside of a week) 5 to 90%RH
Maximum wet bulb temperature
29°C (no condensation)
Operating (*3)
0.3 mm (5 to 20Hz)/0.5G (20 to 250 Hz) or less
Non-operating (*4)
3.1 mm (5 to 20Hz)/5G (20 to 250Hz) or less
Packaged
3.1 mm (5 to 20Hz)/5G (20 to 250Hz) or less
Operating
20G (2 ms)
Non-operating
175G (2 ms)
Operating
–60 m to 3,000 m
Non-operating
–60 m to 12,000 m
+12 VDC ±5%
Ready (Average)
0.4 A
0.25 A
0.9 A
0.65 A
Peak within
100
μ
s at spin-up
3.0 A
3.2 A
3.0 A
Random W/R
(about 80 IOPS)
0.8 A
0.7 A
1.3 A
1.0 A
+5 VDC ±5%
(*6)
Ready
0.6 A
0.8 A
0.7 A
Random W/R
(about 80 IOPS)
6.8 A
1.0 A
0.9 A
Ripple (*7)
+5 V 250 mVp-p, +12 V 250 mVp-p
(*1)
For detail condition, see Section 4.1.
(*2)
Vibration applied to the drive is measured at near the mounting screw hole on the frame as
much as possible.
(*3)
At random seek write/read and default on retry setting with log sweep vibration.
(*4)
At power-off state after installation
Vibration displacement should be less than 2.5 mm.
(*5)
Input voltages are specified at the connector.
(*6)
The terminator power pin (SCSI connector) which supplies power to other terminators is not
used (See Section 4.3).
(*7)
High frequency noise is less than 100 mVp-p.
Power
requirements
Input power (*5)
Altitute
(above sea level)
Shock (*2)
Vibration (*2)
Relative humidity
Temperature (*1)