Garmin Edge 1040 Solar Owners Manual - Page 71

Installing the Out-Front Mount, Releasing the Edge

Get Garmin Edge 1040 Solar PDF manuals and user guides View all Garmin Edge 1040 Solar manuals
Add to My Manuals
Save this manual to your list of manuals

Page 71 highlights

Installing the Out-Front Mount NOTE: If you do not have this mount, you can skip this task. 1 Select a secure location to mount the Edge device where it does not interfere with the safe operation of your bike. 2 Use the hex key to remove the screw from the handlebar connector . 3 Place the rubber pad around the handlebar: • If the handlebar diameter is 25.4 mm or 26 mm, use the thicker pad. • If the handlebar diameter is 31.8 mm, use the thinner pad. • If the handlebar diameter is 35 mm, do not use a rubber pad. 4 Place the handlebar connector around the rubber pad. 5 Replace and tighten the screw. NOTE: Garmin recommends tightening the screw so the mount is secure, with a maximum torque specification of 7 lbf-in. (0.8 N-m). You should check the tightness of the screw periodically. 6 Align the tabs on the back of the Edge device with the bike mount notches . 7 Press down slightly and turn the Edge device clockwise until it locks into place. Releasing the Edge 1 Turn the Edge clockwise to unlock the device. 2 Lift the Edge off the mount. Device Information 65

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
Installing the Out-Front Mount
NOTE:
If you do not have this mount, you can skip this task.
1
Select a secure location to mount the Edge device where it does not interfere with the safe operation of your
bike.
2
Use the hex key to remove the screw
from the handlebar connector
.
3
Place the rubber pad around the handlebar:
•
If the handlebar diameter is 25.4 mm or 26 mm, use the thicker pad.
•
If the handlebar diameter is 31.8 mm, use the thinner pad.
•
If the handlebar diameter is 35 mm, do not use a rubber pad.
4
Place the handlebar connector around the rubber pad.
5
Replace and tighten the screw.
NOTE:
Garmin recommends tightening the screw so the mount is secure, with a maximum torque
specification of 7 lbf-in. (0.8 N-m). You should check the tightness of the screw periodically.
6
Align the tabs on the back of the Edge device with the bike mount notches
.
7
Press down slightly and turn the Edge device clockwise until it locks into place.
Releasing the Edge
1
Turn the Edge clockwise to unlock the device.
2
Lift the Edge off the mount.
Device Information
65