Garmin StreetPilot 7200 Owner's Manual for European Units - Page 58

To slide the puck into the mounting base, To remove the puck from the mounting cradle

Get Garmin StreetPilot 7200 - Automotive GPS Receiver PDF manuals and user guides
UPC - 753759047993
View all Garmin StreetPilot 7200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

Appendix To slide the puck into the mounting base: Locking lever on the mounting base Locking lever on the cradle Sliding the Puck into the Base 1. Slide the puck on the bottom of the mounting cradle into the mounting base. 2. Slide the base's locking lever to the right (locked). 3. Plug the power cable into a 12-Volt receptacle in your vehicle. 4. Route the cable so it does not interfere with vehicle operation. 50 To remove the puck from the mounting cradle: 1. Slide the cradle's locking lever to the left, swing the cradle backward, and pull the cradle off of the StreetPilot. 2. Remove the two screws from the front of the cradle. 3. Remove the two screws, one on each side, near the bottom of the cradle (see image below). Remove four screws to remove the puck and expose the 4-hole pattern. The puck mounting adapter is now detached from the mount, allowing you to mount the StreetPilot 7200/7500 using a standard AMPS 4-hole mounting system. StreetPilot 7200/7500 Owner's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
50
StreetPilot 7200/7500 Owner’s Manual
A
PPENDIX
To slide the puck into the mounting base:
Sliding the Puck into the Base
Locking
lever on the
mounting base
Locking lever
on the cradle
1. Slide the puck on the bottom of the mounting
cradle into the mounting base.
2. Slide the base’s locking lever to the right (locked).
3. Plug the power cable into a 12-Volt receptacle in
your vehicle.
4. Route the cable so it does not interfere with
vehicle operation.
To remove the puck from the mounting cradle:
1. Slide the cradle’s locking lever to the left, swing
the cradle backward, and pull the cradle off of the
StreetPilot.
2. Remove the two screws from the front of the
cradle.
3. Remove the two screws, one on each side, near
the bottom of the cradle (see image below).
Remove four screws
to remove the puck
and expose the 4-hole
pattern.
The puck mounting adapter is now detached from the
mount, allowing you to mount the StreetPilot 7200/7500
using a standard AMPS 4-hole mounting system.