Garmin zumo Owners Manual - Page 25

4 Gently wipe the screen with the cloth. Avoiding Theft • Remove the device and mount from sight when not in use. • Remove the residue left on the windshield by the suction cup. • Do not keep your unit in the glove compartment. • Register your device using the Garmin Express software (garmin.com/express). Restarting the Device You can restart your device if it stops functioning. Hold the power key for 12 seconds. Removing the Device, Mount, and Suction Cup Removing the Device from the Mount 1 Press the release tab or button on the mount. 2 Tilt the bottom of the device upward, and lift the device from the mount. Removing the Mount from the Suction Cup 1 Turn the device mount to the right or left. 2 Apply pressure until the socket on the mount releases the ball on the suction cup. Removing the Suction Cup from the Windshield 1 Flip the lever on the suction cup toward you. 2 Pull the tab on the suction cup toward you. Changing the Fuse in the Vehicle Power Cable NOTICE When replacing the fuse, do not lose any of the small pieces and make sure they are put back in the proper position. The vehicle power cable does not work unless it is assembled correctly. If your device does not charge in your vehicle, you may need to replace the fuse located at the tip of the vehicle adapter. 1 Rotate the end piece counter clockwise to unlock it. TIP: You may need to use a coin to remove the end piece. 2 Remove the end piece, the silver tip , and the fuse . 3 Insert a new fast-blow fuse that has the same current, such as 1 A or 2 A. 4 Place the silver tip in the end piece. 5 Push in the end piece and rotate it clockwise to lock it back into the vehicle power cable . Troubleshooting The suction cup will not stay on my windshield 1 Clean the suction cup and windshield with rubbing alcohol. 2 Dry with a clean, dry cloth. 3 Mount the suction cup (Mounting Your Device in an Automobile, page 3). My device is not acquiring satellite signals • Verify the GPS simulator is turned off (Navigation Settings, page 18). • Take your device out of parking garages and away from tall buildings and trees. • Remain stationary for several minutes. My battery does not stay charged for very long • Decrease the screen brightness (Display Settings, page 18). • Shorten the display timeout (Display Settings, page 18). • Decrease the volume (Adjusting the Volume, page 1). • Turn off the wi-fi radio when it is not in use (Wi‑Fi Settings, page 18). • Put the device in power saving mode when not in use (Turning the Device On or Off, page 1). • Keep your device away from extreme temperatures. • Do not leave your device in direct sunlight. My device does not connect to my phone • Select Settings > Wireless Networks. The Bluetooth option must be enabled. • Enable Bluetooth wireless technology on your phone and bring your phone within 10 m (33 ft.) of the device. • Verify your phone is compatible. Go to www.garmin.com/bluetooth for more information. • Complete the pairing process again. To repeat the pairing process, you must unpair your phone and device (Disconnecting a Bluetooth Device, page 14), and complete the pairing process (Pairing Your Phone and Headset, page 13). My device does not appear as a removable drive on my computer On most computers, the device connects using Media Transfer Protocol (MTP). In MTP mode, the device appears as a portable device and not as a removable drive. My device does not appear as a portable device on my computer On Mac® computers and some Windows® computers, the device connects using USB mass storage mode. In USB mass storage mode, the device appears as a removable drive or volume, and not as a portable device. Windows versions prior to Windows XP Service Pack 3 use USB mass storage mode. My device does not appear as either a portable device or a removable drive or volume on my computer 1 Disconnect the USB cable from your computer. 2 Turn off the device. 3 Connect the USB cable to your device and to a USB port on your computer. TIP: The USB cable must connect to a USB port on your computer, not to a USB hub. The device turns on automatically and goes into MTP mode or USB mass storage mode. A picture of the device connected to a computer appears on the device screen. NOTE: If you have several network drives mapped on your computer, Windows may have trouble assigning drive letters to your Garmin drives. For information about assigning drive letters, see the help file for your operating system. Troubleshooting 21