Home » HP Manuals » Storage Devices » HP 1606 » Manual Viewer

HP 1606 Fabric Watch Administrator's Guide v6.4.0 (53-1001770-01, June 2010) - Page 105

System monitoring using the sysMonitor command, Canceling sysMonitor command configurations

Add to My Manuals
Save this manual to your list of manuals

Page 105 highlights

System monitoring using the sysMonitor command 8 System monitoring using the sysMonitor command Use the sysMonitor command to configure thresholds for Fabric Watch event monitoring for temperature and system resources on the switch. For detailed information about the sysMonitor command, refer to the Fabric OS Command Reference Manual. The following operations are supported by this command: • Configure thresholds for Fabric Watch event monitoring and reporting for the environment and resource classes. Environment thresholds enable temperature monitoring, and resource thresholds enable monitoring of flash memory. Configuration changes are saved persistently to non-volatile storage, but the changes do not take effect until you execute --apply. The --apply option allows you to toggle between default settings and your own saved custom configuration and to apply actions and thresholds separately. • Configure memory or CPU usage parameters on the switch or display memory or CPU usage. Configuration options include setting usage thresholds which, if exceeded, trigger a set of specified Fabric Watch alerts. You can set up the system monitor to poll at certain intervals and specify the number of retries required before Fabric Watch takes action. Configuring thresholds for CPU and memory does not follow the transaction model of the typical Fabric Watch command. The --apply and --cancel options are not valid in this context. When the system crosses any of the limits, SNMP, RASlog, e-mail (or all) messages are generated. Flash and temperature configuration are at the chassis level. To execute this command, you must have chassis-level permission in a virtual fabric (VF) environment. NOTE Spikes in memory and CPU utilization are normal during the firmware download process and you may see threshold warning messages while the process is running. After the firmware download process has completed, memory and CPU utilization should return to normal. System monitoring is disabled by default. You must run both the --config -mem and the --config -cpu commands to enable both memory and CPU system monitoring. Canceling sysMonitor command configurations To cancel unsaved threshold or alarms configurations, enter the cancel command. sysmonitor --cancel class -area area [-thresh_level def | custom] [-action_level def | cust] Using the nosave command The nosave command prevents the configuration changes from being saved persistently. This option allows you to make and view changes without overwriting the saved configuration. CAUTION When you use --config with the --nosave option and the switch reboots, your changes are lost Fabric Watch Administrator's Guide 85 53-1001770-01

Section	Page
About This Document	15
In this chapter	15
How this document is organized	15
Supported hardware and software	16
What’s new in this document	16
New information	16
Changed information	17
Removed information	17
Document conventions	17
Text formatting	17
Notes, cautions, and warnings	18
Key terms	18
Additional information	18
Other industry resources	19
Getting technical help	19
Document feedback	20
Fabric Watch	21
In this chapter	21
Fabric health	21
Fabric Watch overview	22
Role-based access control	22
Fabric Watch licensing	22
Fabric Watch threshold components	23
Switch monitoring components	23
Fabric events monitoring	23
Performance monitoring	23
Security monitoring	24
SFP monitoring	24
Port monitoring	24
System resource monitoring	26
Threshold monitoring using SNMP tables	27
MIB capability configuration parameters	27
Fabric Watch event settings	27
Types of event behaviors	28
Fabric Watch notification types	29
E-mail alert	29
SNMP traps	29
RASlog (switch event)	30
Locked port log	30
Fabric Watch audit messages	30
Data values	31
Reasons to customize Fabric Watch settings	31
Monitoring	32
Threshold and action configuration	32
Event behavior configuration	32
Time base configuration	32
Alert configuration	33
Post-processing of messages	33
Fabric Watch Thresholds	35
In this chapter	35
Threshold values	35
High and low thresholds	35
Buffer values	35
Time bases	37
Time base set to none	37
Time base set to other than none	37
Threshold triggers	39
Above event trigger	39
Below event trigger	40
Changed event trigger	40
Fabric Watch alarm behavior	41
Fabric Watch Threshold Components	43
In this chapter	43
Fabric Watch classes, areas, and elements	43
Classes	43
Class areas	43
Elements	44
Fabric Watch Activation	47
In this chapter	47
Interfaces for activating Fabric Watch	47
Activating Fabric Watch using a Telnet session	47
Activating Fabric Watch using Web Tools	48
Activating Fabric Watch using SNMP	49
Fabric Watch Configuration	53
In this chapter	53
Fabric Watch configuration tasks	53
Setting Fabric Watch custom and default values	55
E-mail notification configuration	55
Showing e-mail configuration information	55
Disabling an e-mail alert	56
Enabling an e-mail alert	56
Sending a test e-mail message	57
Setting recipient e-mail address for e-mail alert	57
Setting the relay host IP address	58
Displaying the relay host configuration	58
Removing the relay host configuration	58
Notification configuration	59
Configuring alarm notifications	59
Fabric, Security, SFP, and Performance Monitoring	61
In this chapter	61
Fabric monitoring guidelines and default settings	61
Fabric class areas	61
Fabric monitoring setting guidelines	62
Fabric class default settings	63
Security monitoring guidelines and default settings	64
Security class areas	64
Security monitoring setting guidelines	64
Security class default settings	65
SFP monitoring guidelines and default settings	67
SFP class areas	67
SFP monitoring setting guidelines	67
SFP class default settings	68
Performance monitoring guidelines and default settings	69
Performance Monitor class areas	69
Performance monitoring setting guidelines	69
Performance Monitor class default settings	69
Configuration options for thConfig command	71
Customizing thConfig command settings	72
Using the nosave command	72
thConfig command restriction	72
Example of thConfig command	73
Recommended settings for Fabric, SFP, Performance, and Security monitoring	74
Port Monitoring	77
In this chapter	77
Port class areas	77
Port class guidelines and default settings	79
Physical port setting guidelines	79
Port class default settings	79
E_Port subclass setting guidelines	81
E_Port class default settings	82
FOP_Port and FCU_Port subclass setting guidelines	84
FOP_Port and FCU_Port subclass default settings	85
VE_Port class default settings	87
Port configuration	88
Custom port settings	88
Using the nosave command	88
portThConfig command procedures	89
Port type: physical port	89
Port type: E_Port	90
Setting the port persistence time	94
Port fencing	94
Recommended high port fencing thresholds	95
Recommended low port fencing thresholds	95
Port fencing configuration using the portFencing command	95
Port fencing configuration using DCFM	96
Recommended port configuration settings	98
System Monitoring	101
In this chapter	101
Environment monitoring	101
Environment class area	101
Environment monitoring setting guidelines	102
Environment class default settings	102
Resource class settings	104
Resource class area	104
Resource class setting guidelines	104
Resource class default settings	104
System monitoring using the sysMonitor command	105
Canceling sysMonitor command configurations	105
Using the nosave command	105
Environment class settings	106
CPU and memory	107
Recommended environment and resource monitoring settings	108
Switch monitoring	109
Switch status policy planning	109
FRU monitoring	111
FRU class areas	111
Configuring FRUs	111
Specifying triggers for FRU alarms	112
Recommended FRU settings	113
Fabric Watch Reports	115
In this chapter	115
Fabric Watch reports	115
Switch Availability Monitor report	116
Generating a Switch Availability Monitor report	116
Switch Health report	117
Generating a Switch Health report	117
Switch Status Policy report	118
Generating a Switch Status Policy report	118
Port Detail report	119
Generating a Port Detail report	119
In this appendix	121
Port threshold configuration using the fwConfigure command	121
Setting port thresholds using the fwConfigure command	122
Refreshing a threshold configuration	124
Disabling a threshold configuration	124
Enabling a threshold	125
Enabling and disabling all port thresholds	125
Changing the threshold boundary level	126
Configuring port fencing using the fwConfigure command	129
Advanced options using the fwConfigure command	132
Changing the numerical values of notification methods	134

Match case Limit results 1 per page

Fabric Watch Administrator’s Guide

53-1001770-01

System monitoring using the sysMonitor command

Use the

sysMonitor

command to configure thresholds for Fabric Watch event monitoring for

temperature and system resources on the switch. For detailed information about the

sysMonitor

command, refer to the

Fabric OS Command Reference Manual

The following operations are supported by this command:

•

Configure thresholds for Fabric Watch event monitoring and reporting for the environment and

resource classes. Environment thresholds enable temperature monitoring, and resource

thresholds enable monitoring of flash memory.

Configuration changes are saved persistently to non-volatile storage, but the changes do not

take effect until you execute --

apply

. The --

apply

option allows you to toggle between default

settings and your own saved custom configuration and to apply actions and thresholds

separately.

•

Configure memory or CPU usage parameters on the switch or display memory or CPU usage.

Configuration options include setting usage thresholds which, if exceeded, trigger a set of

specified Fabric Watch alerts. You can set up the system monitor to poll at certain intervals and

specify the number of retries required before Fabric Watch takes action. Configuring

thresholds for CPU and memory does not follow the transaction model of the typical Fabric

Watch command. The --

apply

and --

cancel

options are not valid in this context.

When the system crosses any of the limits, SNMP, RASlog, e-mail (or all) messages are generated.

Flash and temperature configuration are at the chassis level. To execute this command, you must

have chassis-level permission in a virtual fabric (VF) environment.

NOTE

Spikes in memory and CPU utilization are normal during the firmware download process and you

may see threshold warning messages while the process is running. After the firmware download

process has completed, memory and CPU utilization should return to normal.

System monitoring is disabled by default. You must run both the

--config -mem

and the

--config -cpu

commands to enable both memory and CPU system monitoring.

Canceling sysMonitor command configurations

To cancel unsaved threshold or alarms configurations, enter the

cancel

command.

sysmonitor

cancel class -area area [-thresh_level def | custom] [-action_level

def | cust]

Using the nosave command

The

nosave

command prevents the configuration changes from being saved persistently. This

option allows you to make and view changes without overwriting the saved configuration.

CAUTION

When you use --config with the --nosave option and the switch reboots, your changes are lost