HP AA988A HP StorageWorks 2012sa Modular Smart Array user guide (488320-002, J - Page 31

Attach each side bracket to a rear bracket using #8-32 x 1/4 screws four per

Get HP AA988A - Modular Smart Array Storage Controller SCSI PDF manuals and user guides
UPC - 829160184661
View all HP AA988A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

Figure 2-2 Side Bracket With Alignment Marks b. On one side, insert the first two screws through the side bracket slots above and below the alignment mark into the rear-most threaded holes in the enclosure. For example, to mount the enclosure in a 28-inch deep rack, position the side bracket so that the 28-inch alignment mark is aligned with the rear-most threaded holes in the enclosure. c. Insert up to six more screws through the side bracket slots into the other threaded holes in the side of the enclosure. d. Repeat Step b and Step c to attach the other side bracket to the enclosure. 6. Attach the rear brackets to the rear vertical posts of the rack using #'10-32 x 5/8 screws (two per bracket). 7. Lift the enclosure and slide the side brackets into the rear brackets, which are attached to the rear posts. Adjust the depth of the side brackets so that the slots nearest the ends of the side brackets align with the four PEM nuts in the rear brackets. 8. Attach each side bracket to a rear bracket using #8-32 x 1/4 screws (four per bracket). 9. Ensure that the enclosure is level, and then, secure the mounting ears on the front of the enclosure to the rack face using #10-32 x 5/8 screws (two per ear). 10. Tighten the screws on the side brackets. 11. If you removed modules from the enclosure, reinsert them. 12. If you attached the optional front support nylon brackets to the rack face, remove those brackets. Note - When you finish installing an enclosure, you may have unused screws left in your rack kit; extra screws are provided in case any are misplaced. Chapter 2 Installing and Cabling Enclosures 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
Chapter 2
Installing and Cabling Enclosures
31
Figure 2-2
Side Bracket With Alignment Marks
b. On one side, insert the first two screws through the side bracket slots above and
below the alignment mark into the rear-most threaded holes in the enclosure.
For example, to mount the enclosure in a 28-inch deep rack, position the side
bracket so that the 28-inch alignment mark is aligned with the rear-most threaded
holes in the enclosure.
c.
Insert up to six more screws through the side bracket slots into the other threaded
holes in the side of the enclosure.
d. Repeat Step b and Step c to attach the other side bracket to the enclosure.
6.
Attach the rear brackets to the rear vertical posts of the rack using #‘10-32 x 5/8
screws (two per bracket).
7.
Lift the enclosure and slide the side brackets into the rear brackets, which are
attached to the rear posts.
Adjust the depth of the side brackets so that the slots nearest the ends of the
side
brackets
align with the four PEM nuts in the
rear brackets
.
8.
Attach each side bracket to a rear bracket using #8-32 x 1/4 screws (four per
bracket).
9.
Ensure that the enclosure is level, and then, secure the mounting ears on the front of
the enclosure to the rack face using #10-32 x 5/8 screws (two per ear).
10.
Tighten the screws on the side brackets.
11.
If you removed modules from the enclosure, reinsert them.
12.
If you attached the optional front support nylon brackets to the rack face, remove
those brackets.
Note –
When you finish installing an enclosure, you may have unused screws left
in your rack kit; extra screws are provided in case any are misplaced.