HP AA988A HP StorageWorks 2012sa Modular Smart Array user guide (488320-002, J - Page 45

If you cannot access your system three minutes, after changing the IP address

Get HP AA988A - Modular Smart Array Storage Controller SCSI PDF manuals and user guides
UPC - 829160184661
View all HP AA988A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

As shown in the following example, network parameters, including the IP address, gateway address, and subnet mask are displayed for each controller. Network Parameters Controller A IP Address : 192.168.0.10 Gateway : 192.168.0.1 Subnet Mask : 255.255.0.0 MAC Address : 00:00:FF:D5:01:4D Addressing Mode : Manual Network Parameters Controller B IP Address : 192.168.0.11 Gateway : 192.168.0.1 Subnet Mask : 255.255.0.0 MAC Address : 00:C0:FF:D5:01:15 Addressing Mode : Manual 8. In the host computer's command window, type the following command to verify Ethernet connectivity, first for controller A and then for controller B: ping IP-address If you cannot access your system three minutes after changing the IP address, your network might require you to restart the management controller using the CLI. When you restart a management controller, communication with it is temporarily lost until it successfully restarts. Type the following command to restart the management controller on both controllers: restart mc both 9. After you have verified Ethernet connectivity, disconnect the serial cable and exit the emulator. Chapter 4 Configuring a System for the First Time 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
Chapter 4
Configuring a System for the First Time
45
As shown in the following example, network parameters, including the IP address,
gateway address, and subnet mask are displayed for each controller.
8.
In the host computer's command window, type the following command to verify
Ethernet connectivity, first for controller A and then for controller B:
If you cannot access your system three minutes
after changing the IP address
,
your network might require you to restart the management controller using the CLI.
When you restart a management controller, communication with it is temporarily
lost until it successfully restarts.
Type the following command to restart the management controller on both
controllers:
9.
After you have verified Ethernet connectivity, disconnect the serial cable and exit
the emulator.
Network Parameters Controller A
--------------------------------
IP Address
: 192.168.0.10
Gateway
: 192.168.0.1
Subnet Mask
: 255.255.0.0
MAC Address
: 00:00:FF:D5:01:4D
Addressing Mode
: Manual
Network Parameters Controller B
--------------------------------
IP Address
: 192.168.0.11
Gateway
: 192.168.0.1
Subnet Mask
: 255.255.0.0
MAC Address
: 00:C0:FF:D5:01:15
Addressing Mode
: Manual
ping
IP-address
restart mc both