HP DL560 ProLiant DL560 Server Maintenance and Service Guide - Page 23

Universal Hot-Plug Tape Drive, Tape Drive Blank, Hard Drive Blank

Get HP DL560 - ProLiant - 1 GB RAM PDF manuals and user guides
UPC - 808736876919
View all HP DL560 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

Removal and Replacement Procedures 23 Universal Hot-Plug Tape Drive To remove the component: CAUTION: To prevent improper cooling and thermal damage, do not operate the server unless all bays are populated with either a component or a blank. To replace the Universal Hot-Plug tape drive, slide the drive into the bay until it locks into place. Tape Drive Blank To remove the component: 1. Remove the hot-plug SCSI hard drive, if one is installed, below the tape drive blank ("Hot-Plug SCSI Hard Drive" on page 19). 2. Remove the hard drive blank, if one is installed, below the tape drive blank ("Hard Drive Blank" on page 20). CAUTION: To prevent improper cooling and thermal damage, do not operate the server unless all bays are populated with either a component or a blank.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
Removal and Replacement Procedures
23
Universal Hot-Plug Tape Drive
To remove the component:
CAUTION:
To prevent improper cooling and thermal damage,
do not operate the server unless all bays are populated with either a
component or a blank.
To replace the Universal Hot-Plug tape drive, slide the drive into the bay until it
locks into place.
Tape Drive Blank
To remove the component:
1.
Remove the hot-plug SCSI hard drive, if one is installed, below the tape
drive blank ("Hot-Plug SCSI Hard Drive" on page
19
).
2.
Remove the hard drive blank, if one is installed, below the tape drive blank
("Hard Drive Blank" on page
20
).
CAUTION:
To prevent improper cooling and thermal damage,
do not operate the server unless all bays are populated with either a
component or a blank.