HP Integrity Superdome SX1000 Internal Cabling Guide for HP Smart Array Contro - Page 23

Smart Array Controller Card with Dual Partition Cabling, Step 1.

Get HP Integrity Superdome SX1000 PDF manuals and user guides View all HP Integrity Superdome SX1000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

Cabling for the HP Integrity rx8640 Server Dual Partition Configurations Figure 2-6 Smart Array Controller Card with Dual Partition Cabling Removable Media Cable Bundle Ties PCI Lift Handle Port A1 and Top Right HDD Cable Connections Port A2 and Top Left HDD Cable Connections RAID Cabling for IO Chassis 1 (Bottom Left and Bottom Right Hot Plug Hard Drives) To set up the RAID cabling on the bottom left and bottom right hot plug hard drives, do the following, from the front of the server: Step 1. Verify that the HP Smart Array controller card is installed in PCI slot 8 of IO Chassis 1. Step 2. Retrieve two cables from the cable kit (A7027-63001). Step 3. Identify the new cables using the colored cable ties which are also contained in the cable kit (for each cable, use two of the same color, one on each end). Using a different color tie on each cable makes it easier to identify the cables for installation and servicing. NOTE One end of each cable has a pull-tab connected to the SCSI connector which is labeled "This Connector to PCI Card". This end of the cable connects to the HP Smart Array card. Chapter 2 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
Cabling for the HP Integrity rx8640 Server
Dual Partition Configurations
Chapter 2
19
Figure 2-6 Smart Array Controller Card with Dual Partition Cabling
RAID Cabling for IO Chassis 1 (Bottom Left and Bottom Right Hot Plug Hard
Drives)
To set up the RAID cabling on the bottom left and bottom right hot plug hard drives, do the following, from
the front of the server:
Step 1.
Verify that the HP Smart Array controller card is installed in PCI slot 8 of IO Chassis 1.
Step 2.
Retrieve two cables from the cable kit (A7027-63001).
Step 3.
Identify the new cables using the colored cable ties which are also contained in the cable kit (for
each cable, use two of the same color, one on each end). Using a different color tie on each cable
makes it easier to identify the cables for installation and servicing.
NOTE
One end of each cable has a pull-tab connected to the SCSI connector which is
labeled “This Connector to PCI Card”. This end of the cable connects to the HP Smart
Array card.
Port A2 and Top Left HDD
Cable Connections
Port A1 and Top Right HDD
Cable Connections
Removable Media
Cable Bundle
Ties
PCI Lift Handle