HP Integrity Superdome SX1000 Internal Cabling Guide for HP Smart Array Contro - Page 52

SCSI Cable Routed Through Cable Guide, Folded SCSI Connector, Step 9.

Get HP Integrity Superdome SX1000 PDF manuals and user guides View all HP Integrity Superdome SX1000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

Cabling for the HP Integrity rx7640 Server Recabling for RAID Step 9. Carefully route the round SCSI cable through the cable guide attached to the system backplane to the front of the server. The cable follows the same path as the flat SCSI ribbon cable already installed in the server. See Figure 5-3. Figure 5-3 SCSI Cable Routed Through Cable Guide Step 10. Unplug the existing SCSI ribbon cable for the top left HDD and fold the SCSI connector on the ribbon cable so it will lay in front of the connector on the Mass Storage Backplane. See Figure 5-4. Figure 5-4 Folded SCSI Connector Step 11. Plug the new cable into the mass storage connector for the top left drive. Step 12. Pull any excess cable into the PCI card cage of the server. Step 13. Install the HP Smart Array Controller Card into slot 8 of IO chassis 1 of the server. Step 14. Install the LAN SCSI Core IO card into slot 7 of IO chassis 1 of the server. Step 15. Connect the flat SCSI cable to port A1 of the HP Smart Array Controller Card. (closest to the front of the server). Step 16. Connect the round SCSI cable to port A2 of the HP Smart Array Controller Card. (closest to the rear of the server). Step 17. Re-connect any other cables disconnected during installation. 48 Chapter 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
Cabling for the HP Integrity rx7640 Server
Recabling for RAID
Chapter 5
48
Step 9.
Carefully route the round SCSI cable through the cable guide attached to the system backplane to
the front of the server. The cable follows the same path as the flat SCSI ribbon cable already
installed in the server. See Figure 5-3.
Figure 5-3 SCSI Cable Routed Through Cable Guide
Step 10.
Unplug the existing SCSI ribbon cable for the top left HDD and fold the SCSI connector on the
ribbon cable so it will lay in front of the connector on the Mass Storage Backplane. See Figure 5-4.
Figure 5-4 Folded SCSI Connector
Step 11.
Plug the new cable into the mass storage connector for the top left drive.
Step 12.
Pull any excess cable into the PCI card cage of the server.
Step 13.
Install the HP Smart Array Controller Card into slot 8 of IO chassis 1 of the server.
Step 14.
Install the LAN SCSI Core IO card into slot 7 of IO chassis 1 of the server.
Step 15.
Connect the flat SCSI cable to port A1 of the HP Smart Array Controller Card. (closest to the front
of the server).
Step 16.
Connect the round SCSI cable to port A2 of the HP Smart Array Controller Card. (closest to the
rear of the server).
Step 17.
Re-connect any other cables disconnected during installation.