HP Latex 110 Users Guide - Page 95

The substrate-advance check plot, Image-quality maintenance, Substrate advance calib

Get HP Latex 110 PDF manuals and user guides View all HP Latex 110 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 95 highlights

If the printheads are misaligned or you feel unsure about them-for example, because a substrate crash occurred-then align the printheads. See Align the printheads on page 106. 4. The substrate-advance check plot To fine-tune the quality of your print, you may need to adjust the rate at which the substrate advances. The substrate advance determines the placement of dots on the substrate. If the substrate is not advanced correctly, light or dark bands appear in the printed image and the grain in the print may increase. Substrate-advance adjustment is highly recommended, as the substrate advance is not automatically monitored. You can modify the substrate advance from the RIP or front panel with the Substrate Advance parameter in the substrate preset. To print the substrate-advance check plot: 1. Use the same substrate type that you were using when you detected a problem. 2. Check that the selected substrate type is the same as the substrate type that is loaded into the printer. 3. Go to the front panel and press , then Image-quality maintenance > Substrate advance calib > Print adjustment plot. The substrate-advance check plot consists of several columns with a number at the bottom of each one. Locate the lightest of the columns and enter its number into the Substrate Advance parameter for the current substrate preset. The value chosen in this example should be "−6". NOTE: Minor substrate-advance problems (±2 around the 0 value) are unlikely to result in any print-quality problem, especially with print modes of more than 8 passes. ENWW Improve print quality 89

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
If the printheads are misaligned or you feel unsure about them—for example, because a substrate crash
occurred—then align the printheads. See
Align the printheads
on page
106
.
4. The substrate-advance check plot
To fine-tune the quality of your print, you may need to adjust the rate at which the substrate advances. The
substrate advance determines the placement of dots on the substrate. If the substrate is not advanced
correctly, light or dark bands appear in the printed image and the grain in the print may increase.
Substrate-advance adjustment is highly recommended, as the substrate advance is not automatically
monitored.
You can modify the substrate advance from the RIP or front panel with the Substrate Advance parameter in
the substrate preset.
To print the substrate-advance check plot:
1.
Use the same substrate type that you were using when you detected a problem.
2.
Check that the selected substrate type is the same as the substrate type that is loaded into the printer.
3.
Go to the front panel and press
, then
Image-quality maintenance
>
Substrate advance calib
>
Print adjustment plot
.
The substrate-advance check plot consists of several columns with a number at the bottom of each one.
Locate the lightest of the columns and enter its number into the Substrate Advance parameter for the
current substrate preset. The value chosen in this example should be “−6”.
NOTE:
Minor substrate-advance problems (±2 around the 0 value) are unlikely to result in any print-quality
problem, especially with print modes of more than 8 passes.
ENWW
Improve print quality
89