HP ProBook 5220m HP ProBook 5220m Notebook PC - Maintenance and Service Guide - Page 87

Security cable slot bracket, Remove the two PM2.0x5.0 screws

Get HP ProBook 5220m - Notebook PC PDF manuals and user guides View all HP ProBook 5220m manuals
Add to My Manuals
Save this manual to your list of manuals

Page 87 highlights

Security cable slot bracket Before removing the security cable slot bracket, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer. 4. Remove the battery (see Battery on page 40). 5. Remove the following components: a. Switch cover (see Switch cover on page 51) b. Keyboard (see Keyboard on page 53) c. Top cover (see Top cover on page 56) d. System board (see System board on page 71) Remove the security cable slot bracket: 1. Position the computer right-side up with the right side toward you. 2. Remove the two PM2.0x5.0 screws (1) that secure the security cable slot bracket to the base enclosure. 3. Lift the bracket (2) from the rear at an angle up and out. 4. Disconnect the bracket from the power connector. Reverse this procedure to install the security cable slot bracket. Component replacement procedures 79

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
Security cable slot bracket
Before removing the security cable slot bracket, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see
Battery
on page
40
).
5.
Remove the following components:
a.
Switch cover (see
Switch cover
on page
51
)
b.
Keyboard (see
Keyboard
on page
53
)
c.
Top cover (see
Top cover
on page
56
)
d.
System board (see
System board
on page
71
)
Remove the security cable slot bracket:
1.
Position the computer right-side up with the right side toward you.
2.
Remove the two PM2.0x5.0 screws
(1)
that secure the security cable slot bracket to the base
enclosure.
3.
Lift the bracket
(2)
from the rear at an angle up and out.
4.
Disconnect the bracket from the power connector.
Reverse this procedure to install the security cable slot bracket.
Component replacement procedures
79