HP Surestore 15 Slot with DLT7000 HP SureStore DLT Tape Library Models 4115w/4 - Page 64

Admin, Config * New Password

Get HP Surestore 15 Slot with DLT7000 PDF manuals and user guides View all HP Surestore 15 Slot with DLT7000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

NOTE NOTE Operating the Library Setting a New Administration Menu Password Setting a New Administration Menu Password 1 2 → ADMIN * → CONFIG * NEW PASSWORD Change the password to so that only authorized persons can access the library and change operation settings. Do not forget the password. Only a service representative can reset the password to the factory setting. To set a new password: 1. Follow the steps on "Entering the Administration Menu Password" on page 3-9 to enter the existing password. 2. Press NEXT until CONFIG * displays, then press ENTER. 3. Press NEXT or PREV until NEW PASSWORD displays, then press ENTER. 4. NEW 000-000-000 displays, and the first set of zeros flashes. Press NEXT or PREV to display the new numbers you wish to assign the first part of the password, then press ENTER. 5. The second set of zeros flashes. Press NEXT or PREV to display the new numbers you wish to assign the second part of the password, then press ENTER. 6. The last set of zeros flashes. Press NEXT or PREV to display the new numbers you wish to assign the third part of the password, then press ENTER. 7. PASSWORD CHANGED displays. Press CANCEL three times to return to the drive status ("ready" state). Save the new password to flash ROM by power cycling the library, which allows the password to be recovered if the library is powered off for more than ten days. Do not switch off power to the library until the SCSI bus is inactive. Removing power from a SCSI peripheral when the bus is active can result in data loss and/or indeterminate bus states. If the library is connected to a LAN, check with the system administrator before shutting off power to the library. 3-10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
3-10
Operating the Library
Setting a New Administration Menu Password
Setting a New Administration Menu Password
NOTE
Change the password to so that only authorized persons can access the library and
change operation settings. Do not forget the password. Only a service representative
can reset the password to the factory setting.
To set a new password:
1.
Follow the steps on “Entering the Administration Menu Password” on page 3-9
to enter the existing password.
2.
Press
NEXT
until
CONFIG
*
displays, then press
ENTER
.
3.
Press
NEXT
or
PREV
until
NEW
PASSWORD
displays, then press
ENTER
.
4.
NEW
000-000-000
displays, and the first set of zeros flashes.
Press
NEXT
or
PREV
to display the new numbers you wish to assign the first part
of the password, then press
ENTER
.
5.
The second set of zeros flashes.
Press
NEXT
or
PREV
to display the new numbers you wish to assign the second
part of the password, then press
ENTER
.
6.
The last set of zeros flashes.
Press
NEXT
or
PREV
to display the new numbers you wish to assign the third part
of the password, then press
ENTER
.
7.
PASSWORD
CHANGED
displays. Press
CANCEL
three times to return to the drive
status (“ready” state).
NOTE
Save the new password to flash ROM by power cycling the library, which allows the
password to be recovered if the library is powered off for more than ten days.
Do not switch off power to the library until the SCSI bus is inactive. Removing
power from a SCSI peripheral when the bus is active can result in data loss and/or
indeterminate bus states. If the library is connected to a LAN, check with the system
administrator before shutting off power to the library.
1 2
→
ADMIN *
→
CONFIG * NEW PASSWORD