HP Surestore 15 Slot with DLT7000 HP SureStore DLT Tape Library Models 4115w/4 - Page 68

Viewing Current SCSI Address Settings

Get HP Surestore 15 Slot with DLT7000 PDF manuals and user guides View all HP Surestore 15 Slot with DLT7000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 68 highlights

Table 3-3 Operating the Library Setting and Viewing SCSI IDs Interpreting SCSI Bus Status Indicator LEDs Each SCSI bus has an LED to indicate the bus status. SCSI Status Indicators Indication Status Steady green Flashing green No light Flashing red Flashing yellow Port active and OK. Internal (on-board) termination enabled. Port active and OK. Internal (on-board) termination disabled. Port not active or not configured. Bus mismatch or loss of external termination power. Bus off-line for on-line drive replacement. Viewing Current SCSI Address Settings 1 2 → ADMIN * → SCSI IDs * → VIEW IDs * To view the current SCSI address settings: 1. Verify that the drive status displays. If not, press CANCEL until it does. 2. Press NEXT until ADMIN * displays, then press ENTER. 3. Enter the three-part numerical password (see "Entering the Administration Menu Password" on page 3-9). 4. Press NEXT until SCSI IDs * displays, then press ENTER. 5. SET IDS * displays. Press NEXT until VIEW IDS * displays, then press ENTER. 6. BUS # LIB ID # or BUS # DRV # ID * displays. (BUS # LIB ID # stands for the current SCSI ID of the robotics controller. BUS # DRV # ID # is the current SCSI ID setting for the displayed drive number and its associated BUS#.) 7. Press NEXT or PREV to scroll through the current address settings. 8. Press CANCEL until the next operation to perform displays, or until the drive status (library "ready" state) displays. 3-14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
3-14
Operating the Library
Setting and Viewing SCSI IDs
Interpreting SCSI Bus Status Indicator LEDs
Each SCSI bus has an LED to indicate the bus status.
Table 3-3
SCSI Status Indicators
Viewing Current SCSI Address Settings
To view the current SCSI address settings:
1.
Verify that the drive status displays. If not, press
CANCEL
until it does.
2.
Press
NEXT
until
ADMIN
*
displays, then press
ENTER
.
3.
Enter the three-part numerical password (see “Entering the Administration
Menu Password” on page 3-9).
4.
Press
NEXT
until
SCSI
IDs
*
displays, then press
ENTER
.
5.
SET
IDS
*
displays. Press
NEXT
until
VIEW
IDS
*
displays, then press
ENTER
.
6.
BUS
#
LIB
ID
#
or
BUS
#
DRV
#
ID
*
displays. (BUS # LIB ID # stands for
the current SCSI ID of the robotics controller. BUS # DRV # ID # is the current
SCSI ID setting for the displayed drive number and its associated BUS#.)
7.
Press
NEXT
or
PREV
to scroll through the current address settings.
8.
Press
CANCEL
until the next operation to perform displays, or until the drive
status (library “ready” state) displays.
Indication
Status
Steady green
Port active and OK. Internal (on-board) termination
enabled.
Flashing green
Port active and OK. Internal (on-board) termination
disabled.
No light
Port not active or not configured.
Flashing red
Bus mismatch or loss of external termination power.
Flashing yellow
Bus off-line for on-line drive replacement.
1 2
→
ADMIN *
→
SCSI IDs *
→
VIEW IDs *