HP Surestore S10 Service and User Manual (Short- and Long-Wave) - Page 33

HP Surestore S10 - Hub Manual

Get HP Surestore S10 - Hub PDF manuals and user guides View all HP Surestore S10 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

Installation Figure 12 Hub Correctly Installed in a Rack 12. Plug the PDU cable into the cabinet PDU when you are ready to power on the hub. The hub finishes the self-test in less than 15 seconds. Verify that the hub passes the self-test. If the Fault LED (amber) stays on after self-test, the hub failed. Refer to chapter 4, Troubleshooting, or contact an HP service representative for assistance. If the Power LED is not lighted, refer to chapter 4, Troubleshooting, or contact an HP service representative. 13. Reinstall filler panels over the plenum shroud. Procedure 4: Mount the Hub into a Rack (Optional) 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
Procedure 4: Mount the Hub into a Rack (Optional)
31
Installation
Figure 12
Hub Correctly Installed in a Rack
12.
Plug the PDU cable into the cabinet PDU when you are ready to power on the hub. The
hub finishes the self-test in less than 15 seconds. Verify that the hub passes the self-test.
If the Fault LED (amber) stays on after self-test, the hub failed. Refer to chapter 4,
Troubleshooting, or contact an HP service representative for assistance.
If the Power LED is not lighted, refer to chapter 4, Troubleshooting, or contact an HP
service representative.
13.
Reinstall filler panels over the plenum shroud.