HP Surestore S10 Service and User Manual (Short- and Long-Wave) - Page 55

Procedure 5: Reset the Hub

Get HP Surestore S10 - Hub PDF manuals and user guides View all HP Surestore S10 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

The values displayed for memory range represent low-level diagnostics; the values displayed in the status message can be different from the values shown here. 4. Press . The screen displays status messages; for example: FLASH programming will take about 40 seconds FLASH pgm:[$001000:$101000)->[$800000:$900000) > Caution Do not interrupt the display or press any keys during this process. After about 40 seconds, the display continues. When FLASH programming is completed, the checksum appears; for example: FLASH programming will take about 40 seconds FLASH pgm:[$001000:$101000)->[$800000:$900000) > complete, no errors New FLASH checksum = 0x7B04 The value displayed can be different from the example shown here. Then the Boot menu appears again. Procedure 5: Reset the Hub After updating the hub firmware, you must reset the hub for the new firmware to take effect. 1. From the Boot menu, enter 3 to reset the hub and run the hub self-test. The Main menu appears and displays the new hub controller and device agent code version numbers. 2. Verify that the upgrade version numbers are displayed, then go to Procedure 6: Set Manufacturing Values. If the Main menu displays the Hub Controller version as Unknown, continue with step 3. Updating the Hub Firmware 53 RS-232 Interface Functions

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
Updating the Hub Firmware
53
RS-232 Interface
Functions
The values displayed for memory range represent low-level diagnostics; the values
displayed in the status message can be different from the values shown here.
4.
Press <
E
NTER
>. The screen displays status messages; for example:
FLASH programming will take about 40 seconds
FLASH pgm:[$001000:$101000)->[$800000:$900000) >
Caution
Do not interrupt the display or press any keys during this process.
After about 40 seconds, the display continues.
When FLASH programming is completed, the checksum appears; for example:
FLASH programming will take about 40 seconds
FLASH pgm:[$001000:$101000)->[$800000:$900000) > complete, no errors
New FLASH checksum = 0x7B04
The value displayed can be different from the example shown here. Then the Boot
menu appears again.
Procedure 5: Reset the Hub
After updating the hub firmware, you must reset the hub for the new firmware to take
effect.
1.
From the Boot menu, enter
3
to reset the hub and run the hub self-test. The Main menu
appears and displays the new hub controller and device agent code version numbers.
2.
Verify that the upgrade version numbers are displayed, then go to Procedure 6: Set
Manufacturing Values.
If the Main menu displays the Hub Controller version as
Unknown
, continue with step 3.