HP Surestore S10 Service and User Manual (Short- and Long-Wave) - Page 85

The hub is automatically rebooted and additional messages appear

Get HP Surestore S10 - Hub PDF manuals and user guides View all HP Surestore S10 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 85 highlights

After a few minutes, the transfer prompt appears; for example: Done, memory range [$00001000:$00004FFF] Ready to transfer Hub-Controller code from RAM to FLASH Note, once started, this step must not be interrupted Press Enter to start, control-C to cancel The values displayed for memory range represent low-level diagnostics; the values displayed in the status message can be different from the values shown here. 4. Press . Additional progress indicators and status messages appear; for example: The hub is automatically rebooted and additional messages appear: Rebooting to make sure download was successful... DRAM test (this will take about 10 seconds) > passed SEEPROM test (this will take about 1 second ) > passed FLASH checksum (this will take about 2 seconds) > passed Press Enter key for Boot Menu, Agent boot in 6 seconds Then the Main menu appears. Fibre Channel Hub Model Number: Device Agent Version: Hub Controller Version: Agent Boot PROM Version: Status of Device Agent self-test: Status of Hub Controller self-test: HP3724A 02.04 02.02 01.04 passed passed 1. Reset hub and run self-test 2. Set Networking parameters 5. Verify that the Device Agent and Hub Controller versions you reinstalled appear in the Main menu. 6. See Updating the Hub Firmware on page 48 to upgrade to the new firmware versions. Troubleshooting If Firmware Upgrade Appears to Fail 83

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
If Firmware Upgrade Appears to Fail
83
Troubleshooting
After a few minutes, the transfer prompt appears; for example:
Done, memory range [$00001000:$00004FFF]
Ready to transfer Hub-Controller code from RAM to FLASH
Note, once started, this step must not be interrupted
Press Enter to start, control-C to cancel
The values displayed for memory range represent low-level diagnostics; the values
displayed in the status message can be different from the values shown here.
4.
Press <
E
NTER
>. Additional progress indicators and status messages appear; for
example:
--+
$
..................................................................
.........
************************
The hub is automatically rebooted and additional messages appear:
Rebooting to make sure download was successful...
DRAM test
(this will take about 10 seconds)
> passed
SEEPROM test
(this will take about
1 second )
> passed
FLASH checksum (this will take about
2 seconds)
> passed
Press Enter key for Boot Menu, Agent boot in 6 seconds
Then the Main menu appears.
Fibre Channel Hub Model Number:
HP3724A
Device Agent Version:
02.04
Hub Controller Version:
02.02
Agent Boot PROM Version:
01.04
Status of Device Agent self-test:
passed
Status of Hub Controller self-test:
passed
1. Reset hub and run self-test
2. Set Networking parameters
5.
Verify that the Device Agent and Hub Controller versions you reinstalled appear in the
Main menu.
6.
See Updating the Hub Firmware on page 48 to upgrade to the new firmware versions.