HP Surestore S10 Service and User Manual (Short- and Long-Wave) - Page 59

Enabling Hub Management

Get HP Surestore S10 - Hub PDF manuals and user guides View all HP Surestore S10 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

Enabling Hub Management Use the hub RS-232 management menus to enable the hub to be managed by Fibre Channel Manager. To enable hub management: • Set hub IP address and network configuration options. • Set SNMP values. • Configure cascaded hubs (if you plan to manage hubs in a cascaded configuration). Setting Hub IP Address and Network Configuration Options Use this procedure to set the following parameters on the hub. • Hub IP address • Subnetworking mask • Default gateway address If you have hubs in a cascaded configuration, only perform this procedure for the parent hub. The parent hub should be the hub that has the LAN (ethernet) connection. Refer to the values you entered in Table 1 on page 42 as you set the above parameters. To set hub IP address and network configuration options: 1. Set up an RS-232 connection between the parent hub and a PC or dumb terminal (see Setting Up a Connection to a PC on page 45 or Setting Up a Connection to a Dumb Terminal on page 46). Enabling Hub Management 57 RS-232 Interface Functions

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
Enabling Hub Management
57
RS-232 Interface
Functions
Enabling Hub Management
Use the hub RS-232 management menus to enable the hub to be managed by Fibre Channel
Manager. To enable hub management:
•
Set hub IP address and network configuration options.
•
Set SNMP values.
•
Configure cascaded hubs (if you plan to manage hubs in a cascaded configuration).
Setting Hub IP Address and Network Configuration Options
Use this procedure to set the following parameters on the hub.
•
Hub IP address
•
Subnetworking mask
•
Default gateway address
If you have hubs in a cascaded configuration, only perform this procedure for the parent
hub. The parent hub should be the hub that has the LAN (ethernet) connection. Refer to the
values you entered in Table 1 on page 42 as you set the above parameters.
To set hub IP address and network configuration options:
1.
Set up an RS-232 connection between the parent hub and a PC or dumb terminal (see
Setting Up a Connection to a PC on page 45 or Setting Up a Connection to a Dumb
Terminal on page 46).