HP Surestore S10 Service and User Manual (Short- and Long-Wave) - Page 42

Procedure 7: Verify the Connections

Get HP Surestore S10 - Hub PDF manuals and user guides View all HP Surestore S10 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

Procedure 7: Verify the Connections After connecting devices and the server to the hub, verify the connections. Note Because the hub is strictly a pass-through device for FC-AL traffic, there is no hub address and the hub is not listed in ioscan output (HP-UX servers) or the SCSI Adapters window (HP NetServers). For HP-UX servers: 1. Use the following HP-UX command to run ioscan and check the hardware paths between the server and the attached FC-AL devices: ioscan -f For details on ioscan and its options, refer to the HP-UX System Administration Tasks Manual. Also consult the device documentation to interpret the ioscan output. 2. If the Hardware State of a device connected to the hub is "Unclaimed"or "No H/W,"see chapter 4, Troubleshooting, for more information. For HP NetServers: 1. From the Start menu, select Settings, then select Control Panel. 2. Double-click the SCSI Adapters icon. The SCSI Adapters window appears. 3. Click the Devices tab, then verify that the FC-AL devices connected to the hub are displayed. 40 Procedure 7: Verify the Connections

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
40
Procedure 7: Verify the Connections
Procedure 7: Verify the Connections
After connecting devices and the server to the hub, verify the connections.
Note
Because the hub is strictly a pass-through device for FC-AL traffic, there is no
hub address and the hub is not listed in ioscan output (HP-UX servers) or the
SCSI Adapters
window (HP NetServers).
For HP-UX servers:
1.
Use the following HP-UX command to run ioscan and check the hardware paths
between the server and the attached FC-AL devices:
ioscan -f
For details on ioscan and its options, refer to the
HP-UX System Administration
Tasks
Manual
. Also consult the device documentation to interpret the ioscan output.
2.
If the Hardware State of a device connected to the hub is “Unclaimed” or “No H/W,” see
chapter 4, Troubleshooting, for more information.
For HP NetServers:
1.
From the
Start
menu, select
Settings
, then select
Control Panel
.
2.
Double-click the
SCSI Adapters
icon. The SCSI Adapters window appears.
3.
Click the
Devices
tab, then verify that the FC-AL devices connected to the hub are
displayed.