HP Vectra XA 5/xxx HP Vectra xA 5/XXX Series 5 Pc DESKTOP USER’S GUID - Page 42

Warning

Get HP Vectra XA 5/xxx PDF manuals and user guides View all HP Vectra XA 5/xxx manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

2 How to Install Accessories In Your PC Installing Mass Storage Devices 5 Connect the data and power cables to the rear of the device installed in the middle shelf. The connectors are shaped to go in one way only. If you are installing an IDE CD-ROM drive, connect the drive to the CD-ROM data cable. This data cable should be connected to the connector marked "CD-ROM" on the system board. If you are not sure which connector to use, refer to "Connecting IDE Devices", on page 23. WARNING Data cable Power cable 6 Install any other accessories before replacing the cover. Reconnect all cables and power cords. 7 Verify the new configuration by checking the HP Summary Screen. Refer to page 40. Do not open the CD-ROM drive enclosure as there is a danger of electric shock, and the laser beam light could harm your eyes. Service should be carried out by qualified personnel. This PC is a class 1 laser product. To avoid discomfort from unexpected noise, always turn the volume down before connecting headphones or speakers. Listening to loud sounds for prolonged periods may permanently damage your hearing. Before putting on headphones, place them round your neck and turn the volume down. When you put on the headphones, slowly increase the volume until you find a comfortable listening level and leave the volume control in that position. 30 English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
2
How to Install Accessories In Your PC
Installing Mass Storage Devices
30
English
5
Connect the data and power cables to the rear of the device installed
in the middle shelf.
The connectors are shaped to go in one way
only.
If you are installing an IDE CD-ROM drive, connect the drive
to the CD-ROM data cable. This data cable should be connected to
the connector marked “CD-ROM” on the system board. If you are not
sure which connector to use, refer to "Connecting IDE Devices", on
page 23.
6
Install any other accessories before replacing the cover. Reconnect
all cables and power cords.
7
Verify the new configuration by checking the HP Summary Screen.
Refer to page 40.
WARNING
Do not open the CD-ROM drive enclosure as there is a danger of
electric shock, and the laser beam light could harm your eyes. Service
should be carried out by qualified personnel. This PC is a class 1 laser
product. To avoid discomfort from unexpected noise, always turn the
volume down before connecting headphones or speakers. Listening to
loud sounds for prolonged periods may permanently damage your
hearing. Before putting on headphones, place them round your neck
and turn the volume down. When you put on the headphones, slowly
increase the volume until you find a comfortable listening level and
leave the volume control in that position.
Power cable
Data cable