HP XM600 hp kayak xm600, installing and replacing hardware parts in your pc wo - Page 25

Installing a Second Hard Disk Drive in an Internal Shelf, Installing a Third Hard Disk Drive

Get HP XM600 - Kayak - 128 MB RAM PDF manuals and user guides View all HP XM600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

Installing and Replacing Hardware Parts in Your PC Workstation Installing a Second Hard Disk Drive in an Internal Shelf Installing a Second Hard Disk Drive in an Internal Shelf The internal shelves can support two 3.5-inch devices. The master hard disk drive must be installed in the top shelf when using an IDE configuration. To install a second hard disk drive: 1 Switch off the display and PC Workstation. Disconnect all power cables and any LAN or telecommunications cables. 2 Remove the PC Workstation's cover (refer to page 3 for instructions). 3 If the primary hard disk drive is installed in the top shelf, disconnect the data and power cables. 4 Add the short blue guide rails to the new hard disk drive. Insert the guide rail labeled "L" on the left-hand side (cable connectors facing towards you and positioned at the bottom), and the guide rail "R" on the righthand side of the hard disk drive. 5 The second hard disk drive can only be inserted one way. Ensure that the data and cable connectors are facing you and positioned at the top. 6 Align the guide rails on both sides of the drive with the internal shelf guides and then slide the drive into the bottom shelf until it clicks into position. 7 Connect the power and data cables to the second hard disk drive. Reconnect the power cables and the data cable to the primary hard disk drive. 8 Replace the PC Workstation's cover (refer to page 4). Reconnect all the power and telecommunications cables. 9 Turn to page 30 to complete the installation. Installing a Third Hard Disk Drive On some models, a third 3.5-inch hard disk drive can be installed in the front access cage. The installation procedure is explained on page 26, step 4. 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
Installing and Replacing Hardware Parts in Your PC Workstation
Installing a Second Hard Disk Drive in an Internal Shelf
25
Installing a Second Hard Disk Drive in an Internal Shelf
The internal shelves can support two 3.5-inch devices. The master hard
disk drive must be installed in the top shelf when using an IDE
configuration.
To install a second hard disk drive:
1
Switch off the display and PC Workstation. Disconnect all power cables
and any LAN or telecommunications cables.
2
Remove the PC Workstation’s cover (refer to page 3 for instructions).
3
If the primary hard disk drive is installed in the top shelf, disconnect the
data and power cables.
4
Add the short blue guide rails to the new hard disk drive. Insert the guide
rail labeled “L” on the left-hand side (cable connectors facing towards
you and positioned at the bottom), and the guide rail “R” on the right-
hand side of the hard disk drive.
5
The second hard disk drive can only be inserted one way. Ensure that
the data and cable connectors are facing you and positioned at the top.
6
Align the guide rails on both sides of the drive with the internal shelf
guides and then slide the drive into the bottom shelf until it clicks into
position.
7
Connect the power and data cables to the second hard disk drive.
Reconnect the power cables and the data cable to the primary hard disk
drive.
8
Replace the PC Workstation’s cover (refer to page 4). Reconnect all the
power and telecommunications cables.
9
Turn to page 30 to complete the installation.
Installing a Third Hard Disk Drive
On some models, a third 3.5-inch hard disk drive can be installed in the
front access cage. The installation procedure is explained on page 26,
step 4.