Husqvarna AUTOMOWER 550 EPOS Owner Manual - Page 13

CAUTION, 6 To examine where to put the power, supply, WARNING

Get Husqvarna AUTOMOWER 550 EPOS PDF manuals and user guides View all Husqvarna AUTOMOWER 550 EPOS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

• If the product must not operate in a part of the docking area, put a protective wall that is minimum 15 cm / 6 in. in height. The docking area (A) is a circular area around the charging station with a radius of 3 m / 9.8 ft. • If the work area has 2 parts separated with a steep slope, we recommend to put the charging station in the lower section. CAUTION: Metal objects in the ground, for example reinforced concrete or anti-mole nets can cause interference with the charging station signal. 3.6 To examine where to put the power supply WARNING: Do not cut or extend the low-voltage cable. There is a risk of electrical shock. A CAUTION: Make sure that the blades on the product do not cut the low-voltage cable. CAUTION: Do not put the low-voltage cable in a coil or below the charging station plate. The coil causes interference with the signal from the charging station. Note: The product uses the charging station signal to search for the charging station when it is in the docking area. • Put the charging station near a power outlet. • Put the charging station on a level surface. • The baseplate of the charging station must not be bent. max. 5 cm / 2" max. 5 cm / 2" • Put the power supply in an area with a roof and protection from the sun and rain. • Put the power supply in an area with good airflow. • Use a residual-current device (RCD) with a tripping current of maximum 30 mA when you connect the power supply to the power outlet. Low-voltage cables of different lengths are available as accessories. 1576 - 003 - 30.12.2020 Installation - 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
•
If the product must not operate in a part of the
docking area, put a protective wall that is minimum
15 cm / 6 in. in height. The docking area (A) is a
circular area around the charging station with a
radius of 3 m / 9.8 ft.
A
Note:
The product uses the charging station
signal to search for the charging station when it is
in the docking area.
•
Put the charging station near a power outlet.
•
Put the charging station on a level surface.
•
The baseplate of the charging station must not be
bent.
max. 5 cm / 2"
max. 5 cm / 2"
•
If the work area has 2 parts separated with a steep
slope, we recommend to put the charging station in
the lower section.
CAUTION:
Metal objects in the ground,
for example reinforced concrete or anti-mole
nets can cause interference with the
charging station signal.
3.6 To examine where to put the power
supply
WARNING:
Do not cut or extend the
low-voltage cable. There is a risk of
electrical shock.
CAUTION:
Make sure that the blades
on the product do not cut the low-voltage
cable.
CAUTION:
Do not put the low-voltage
cable in a coil or below the charging station
plate. The coil causes interference with the
signal from the charging station.
•
Put the power supply in an area with a roof and
protection from the sun and rain.
•
Put the power supply in an area with good airflow.
•
Use a residual-current device (RCD) with a tripping
current of maximum 30 mA when you connect the
power supply to the power outlet.
Low-voltage cables of different lengths are available as
accessories.
1576 - 003 - 30.12.2020
Installation -
13