Husqvarna AUTOMOWER 550 EPOS Owner Manual - Page 14

To examine where to install the, objects on the map, CAUTION

Get Husqvarna AUTOMOWER 550 EPOS PDF manuals and user guides View all Husqvarna AUTOMOWER 550 EPOS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

3.7 To examine where to install the objects on the map CAUTION: If the work area is adjacent to water bodies, slopes, precipices or a public road, the virtual boundary must have a protective wall. The wall must be minimum 15 cm / 6 in. in height. CAUTION: Do not let the product operate on gravel. CAUTION: For careful operation without noise, isolate all obstacles such as trees, roots and stones. Note: Make a blueprint of the work area before you install the virtual boundaries. • Make sure that the area where the product operates has unimpeded sky view. This means that 110° of the sky in all directions must be unimpeded. The product cannot receive satellite signals that is less than 10% elevation angle. • Make sure that there are no trees with thick vegetation in the areas where the product operates. • Make sure the that product can receive radio signals from the reference station in the complete area. It is recommended to have a free line of sight between the product and the reference station for an optimal performance. 3.7.1 Passages A passage is a section that has virtual boundary on each side and that connects 2 parts of the work area. The passage must be a minimum of 2 m / 6.5 ft. wide to get a good cutting result. Short passages can be as narrow as 1 m / 3.3 ft. A long narrow passage can have a negative impact of the cutting result. A dead end must be a minimum of 2 m / 6.5 ft. wide. 3.7.2 To install the map objects in a slope The product can operate in 45% slopes. Slopes that are too steep must be excluded from the area or isolated as stay-out zones. The gradient (%) is calculated as height per m. Example: 10 cm / 100 cm = 10%. 10% 100 cm/40" 10 cm/4" >110° 35° 35° • For slopes steeper than 45% inside the work area, isolate the slope with a stay-out zone. • For slopes steeper than 15% along the outer edge of the lawn. For installation of the virtual boundary, operate the product with the rear wheel 5 cm / 2 in. (A) from the edge. >110° 60° 10° • Make sure that there are no trees close to the virtual boundaries and along the paths. >15% A • For slopes adjacent to a public road, put a fence or a protective wall along the outer edge of the slope. 14 - Installation 1576 - 003 - 30.12.2020

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
3.7 To examine where to install the
objects on the map
CAUTION:
If the work area is adjacent
to water bodies, slopes, precipices or a
public road, the virtual boundary must have
a protective wall. The wall must be minimum
15 cm / 6 in. in height.
CAUTION:
Do not let the product
operate on gravel.
CAUTION:
For careful operation
without noise, isolate all obstacles such as
trees, roots and stones.
Note:
Make a blueprint of the work area before you
install the virtual boundaries.
•
Make sure that the area where the product
operates has unimpeded sky view. This means
that 110° of the sky in all directions must be
unimpeded. The product cannot receive satellite
signals that is less than 10% elevation angle.
>110°
35°
35°
60°
10°
>110°
•
Make sure that there are no trees close to the
virtual boundaries and along the paths.
•
Make sure that there are no trees with thick
vegetation in the areas where the product
operates.
•
Make sure the that product can receive radio
signals from the reference station in the complete
area. It is recommended to have a free line of sight
between the product and the reference station for
an optimal performance.
3.7.1 Passages
A passage is a section that has virtual boundary on each
side and that connects 2 parts of the work area. The
passage must be a minimum of 2 m / 6.5 ft. wide to get
a good cutting result. Short passages can be as narrow
as 1 m / 3.3 ft. A long narrow passage can have a
negative impact of the cutting result. A dead end must
be a minimum of 2 m / 6.5 ft. wide.
3.7.2 To install the map objects in a slope
The product can operate in 45% slopes. Slopes that are
too steep must be excluded from the area or isolated as
stay-out zones. The gradient (%) is calculated as height
per m. Example: 10 cm / 100 cm = 10%.
10 cm/4"
100 cm/40"
10%
•
For slopes steeper than 45% inside the work area,
isolate the slope with a stay-out zone.
•
For slopes steeper than 15% along the outer edge
of the lawn. For installation of the virtual boundary,
operate the product with the rear wheel 5 cm / 2 in.
(A) from the edge.
A
>15%
•
For slopes adjacent to a public road, put a fence or
a protective wall along the outer edge of the slope.
14
- Installation
1576 - 003 - 30.12.2020