Husqvarna AUTOMOWER 550 EPOS Owner Manual - Page 28

Message, Cause, Action

Get Husqvarna AUTOMOWER 550 EPOS PDF manuals and user guides View all Husqvarna AUTOMOWER 550 EPOS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

Message No loop signal Outside work area Cause Action The power supply or the low-voltage ca- Examine the LED status on the charging ble for the charging station is not connec- station. If there is no power to the charg- ted. ing station, the LED is not lit. Examine the wall socket connection and if a resid- ual-current device is engaged. Make sure that the low-voltage cable is connected to the charging station. The power supply or the low-voltage ca- Replace the power supply or low-voltage ble for the charging station is damaged. cable. ECO mode is enabled and the LED indicator lamp on the charging station is flashing green. The product has been started manually in the work area without pushing the STOP button before removing the product from the charging station. The charging station signal is disabled and the product cannot enter the charging station. Refer to ECO mode on page 21. Put the product in the charging station. Start the product. Refer to To start the product on page 23. The product does not find the loop signal Put the product in the charging station from the charging station. and generate a new loop signal. Refer to New loop signal on page 21. The charging station in not installed correctly. Install the charging station according to the instruction. Refer to To install the charging station on page 15. Interference from metal objects such as Change the position of the charging stafences, reinforcement steel or buried ca- tion. bles near the charging station. The work area slopes too much by the virtual boundary. Make sure that the virtual boundary is installed correctly. Refer to To examine where to install the objects on the map on page 14. The transport path or the path to the point of interest slopes too much. Make sure that the transport path is installed correctly. Refer to To install the map objects in a slope on page 14. The product finds it hard to distinguish the charging station signal from another product installation close by. Put the product in the charging station and generate a new loop signal. Refer to New loop signal on page 21. Interference from metal objects such as Change the position of the charging stafences, reinforcement steel or buried ca- tion. bles near the charging station. 28 - Troubleshooting 1576 - 003 - 30.12.2020

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
Message
Cause
Action
No loop signal
The power supply or the low-voltage ca-
ble for the charging station is not connec-
ted.
Examine the LED status on the charging
station. If there is no power to the charg-
ing station, the LED is not lit. Examine
the wall socket connection and if a resid-
ual-current device is engaged. Make sure
that the low-voltage cable is connected to
the charging station.
The power supply or the low-voltage ca-
ble for the charging station is damaged.
Replace the power supply or low-voltage
cable.
ECO mode
is enabled and the LED indi-
cator lamp on the charging station is
flashing green. The product has been
started manually in the work area without
pushing the
STOP
button before remov-
ing the product from the charging station.
The charging station signal is disabled
and the product cannot enter the charg-
ing station. Refer to
ECO mode on page
21
.
Put the product in the charging station.
Start the product. Refer to
To start the
product on page 23
.
The product does not find the loop signal
from the charging station.
Put the product in the charging station
and generate a new loop signal. Refer to
New loop signal on page 21
.
The charging station in not installed cor-
rectly.
Install the charging station according to
the instruction. Refer to
To install the
charging station on page 15
.
Interference from metal objects such as
fences, reinforcement steel or buried ca-
bles near the charging station.
Change the position of the charging sta-
tion.
Outside work area
The work area slopes too much by the
virtual boundary.
Make sure that the virtual boundary is in-
stalled correctly. Refer to
To examine
where to install the objects on the map
on page 14
.
The transport path or the path to the
point of interest slopes too much.
Make sure that the transport path is in-
stalled correctly. Refer to
To install the
map objects in a slope on page 14
.
The product finds it hard to distinguish
the charging station signal from another
product installation close by.
Put the product in the charging station
and generate a new loop signal. Refer to
New loop signal on page 21
.
Interference from metal objects such as
fences, reinforcement steel or buried ca-
bles near the charging station.
Change the position of the charging sta-
tion.
28
- Troubleshooting
1576 - 003 - 30.12.2020