IBM 4800-741 Operation Guide - Page 63

Connecting, power

Get IBM 4800-741 PDF manuals and user guides View all IBM 4800-741 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

Updated October 31, 2007 Step 8. Connecting the power 1. Connect the power cord to the SurePOS 700 and plug into an electrical outlet. 2. If a UPS is attached, power on the UPS (switch G in Figure 37). B A C DE FG Figure 37. Front panel controls and indicators A Recessed dump switch B System power switch C Headphone jack (Models 741 and 781 only) D Hard disk drive indicator E Power indicator F UPS indicator (only with wide footprint and UPS installed; otherwise covered) G UPS switch (only with wide footprint and UPS installed; otherwise covered) 3. Verify that the UPS indicator light (LED) is on and operating correctly (refer to Table 6). 4. Power on the system unit (switch B ). 5. Verify that the SurePOS 700 is operating correctly by checking the LEDs on the front of the unit. See Table 6. Table 6. Status indicators Indicator Power ( E in Figure 37) HDD ( D ) UPS ( G ) Status v Steady: power on v Blinking: standby v No light: power off v Yellow: HDD activity v Green: using AC power v Slowly blinking: power from internal battery v Blinking rapidly: UPS is supplying power and battery is low Chapter 2. Installation and system setup 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
Step
8.
Connecting
the
power
1.
Connect
the
power
cord
to
the
SurePOS
700
and
plug
into
an
electrical
outlet.
2.
If
a
UPS
is
attached,
power
on
the
UPS
(switch
±G²
in
Figure
37).
A
Recessed
dump
switch
B
System
power
switch
C
Headphone
jack
(Models
741
and
781
only)
D
Hard
disk
drive
indicator
E
Power
indicator
F
UPS
indicator
(only
with
wide
footprint
and
UPS
installed;
otherwise
covered)
G
UPS
switch
(only
with
wide
footprint
and
UPS
installed;
otherwise
covered)
3.
Verify
that
the
UPS
indicator
light
(LED)
is
on
and
operating
correctly
(refer
to
Table
6).
4.
Power
on
the
system
unit
(switch
±B²
).
5.
Verify
that
the
SurePOS
700
is
operating
correctly
by
checking
the
LEDs
on
the
front
of
the
unit.
See
Table
6.
Table
6.
Status
indicators
Indicator
Status
Power
(
±E²
in
Figure
37)
v
Steady:
power
on
v
Blinking:
standby
v
No
light:
power
off
HDD
(
±D²
)
v
Yellow:
HDD
activity
UPS
(
±G²
)
v
Green:
using
AC
power
v
Slowly
blinking:
power
from
internal
battery
v
Blinking
rapidly:
UPS
is
supplying
power
and
battery
is
low
B
A
C
D
E
F
G
Figure
37.
Front
panel
controls
and
indicators
Updated
October
31,
2007
Chapter
2.
Installation
and
system
setup
43