IBM 4800-741 Operation Guide - Page 96

Installing, slanted

Get IBM 4800-741 PDF manuals and user guides View all IBM 4800-741 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 96 highlights

Updated October 31, 2007 3. Place the hooks of the mount into the base of the CRT and slide the mount forward. Turn the CRT right side up. Installing a CRT in a slanted I/O tray 1. Switch the power OFF. 2. Remove any display or printer filler that is installed. 3. If the wedge mount is installed on the left side of the printer, rotate the base so that the display moves to the far left. If the wedge mount is installed on the right side of the print, rotate the base so the display moves to the far right position. It will snap into place. If the wedge mount is installed for a distributed setup, you can install it left centered (as shipped from the factory). Note: If a wedge mount is adjusted with the monitor locked into the far right position and you want to move out of that position, use a screwdriver and lift the spring loop over the retaining ramp on the bottom of the mount. 4. Thread the CRT's video cables and the CRT's power cord down through the rear of the system unit. 5. Attach the CRT's signal cable to the video port on the system unit. 6. Plug the display power cord into a wall using an adapter cable, or into the uninterruptible power supply (if installed). 7. Power ON the SurePOS 700. 76 SurePOS 700 Series: SurePOS 700-721/741/781, 722/742/782 Planning, Installation, and Operation Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
3.
Place
the
hooks
of
the
mount
into
the
base
of
the
CRT
and
slide
the
mount
forward.
Turn
the
CRT
right
side
up.
Installing
a
CRT
in
a
slanted
I/O
tray
1.
Switch
the
power
OFF.
2.
Remove
any
display
or
printer
filler
that
is
installed.
3.
If
the
wedge
mount
is
installed
on
the
left
side
of
the
printer,
rotate
the
base
so
that
the
display
moves
to
the
far
left.
If
the
wedge
mount
is
installed
on
the
right
side
of
the
print,
rotate
the
base
so
the
display
moves
to
the
far
right
position.
It
will
snap
into
place.
If
the
wedge
mount
is
installed
for
a
distributed
setup
,
you
can
install
it
left
centered
(as
shipped
from
the
factory).
Note:
If
a
wedge
mount
is
adjusted
with
the
monitor
locked
into
the
far
right
position
and
you
want
to
move
out
of
that
position,
use
a
screwdriver
and
lift
the
spring
loop
over
the
retaining
ramp
on
the
bottom
of
the
mount.
4.
Thread
the
CRT’s
video
cables
and
the
CRT’s
power
cord
down
through
the
rear
of
the
system
unit.
5.
Attach
the
CRT’s
signal
cable
to
the
video
port
on
the
system
unit.
6.
Plug
the
display
power
cord
into
a
wall
using
an
adapter
cable,
or
into
the
uninterruptible
power
supply
(if
installed).
7.
Power
ON
the
SurePOS
700.
Updated
October
31,
2007
76
SurePOS
700
Series:
SurePOS
700-721/741/781,
722/742/782
Planning,
Installation,
and
Operation
Guide