Icom IC-A14 Instruction Manual - Page 39

Troubleshooting

Get Icom IC-A14 PDF manuals and user guides View all Icom IC-A14 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

9 TROUBLESHOOTING If your transceiver seems to be malfunctioning, please check the following points before sending it to a service center. 1 PROBLEM POSSIBLE CAUSE SOLUTION REF. 2 No power comes on. • The battery is exhausted. • Bad connection for the battery pack. • Recharge the battery pack. • Check the connection to the transceiver. pgs. 29-31 p. 7 3 No sound comes from the • Squelch level is too deep. • Set squelch to the threshold point. p. 9 4 speaker. Transmitting impossible. • Volume level is too low. • WX channels or NAVI band is selected. • The battery is exhausted. • Set [VOL] to a suitable level. • Set COM band in frequency mode. • Recharge the battery pack. p. 8 5 pgs. 29-31 6 Operating frequency or • Lock function is activated. memory channel can not • Push and hold [ ] for 2 sec. to turn the lock p. 9 function OFF. 7 be changed. 8 Scan does not start. • All memory channels in the selected bank are • Set the "TAG" settings of desired channels. p. 20 not programmed as "TAG" channels. 9 No beep sounds. • Squelch is open. • Set the squelch level to tighten. p. 9 10 • There is not more than 2 memorized channels • Program 2 or more memory channels. pgs. 13, 14 • Beep tones turned OFF. • T urn the beep tone ON; 11  IC-A14: Push [FUNC], then push [BEEP](8). p. 22  IC-A14S: Turn the beep tone ON in set mode. pgs. 22, 25 12 13 14 D CP-22 fuse replacement 15 If the fuse blows or the receiver stops functioning while oper- 16 ating with the optional CP-22 cigarette lighter cable, find the source of the problem if possible, and replace the dam- 17 aged fuse with a new rated one (FGB 8 A) as shown right. 18 19 Fuse 8 A 34

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
34
9
TROUBLESHOOTING
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
If your transceiver seems to be malfunctioning, please check the following points before sending it to a service center.
PROBLEM
POSSIBLE CAUSE
SOLUTION
REF.
No power comes on.
• The battery is exhausted.
• Recharge the battery pack.
pgs. 29–31
• Bad connection for the battery pack.
• Check the connection to the transceiver.
p. 7
No sound comes from the
• Squelch level is too deep.
• Set squelch to the threshold point.
p. 9
speaker.
• Volume level is too low.
• Set
[VOL]
to a suitable level.
Transmitting impossible.
• WX channels or NAVI band is selected.
• Set COM band in frequency mode.
p. 8
• The battery is exhausted.
• Recharge the battery pack.
pgs. 29–31
Operating frequency or
• Lock function is activated.
• Push and hold
[
]
for 2 sec. to turn the lock p. 9
memory channel can not
function OFF.
be changed.
Scan does not start.
• All memory channels in the selected bank are
• Set the “TAG” settings of desired channels.
p. 20
not programmed as “TAG” channels.
• Squelch is open.
• Set the squelch level to tighten.
p. 9
• There is not more than 2 memorized channels
• Program 2 or more memory channels.
pgs. 13, 14
No beep sounds.
• Beep tones turned OFF.
•
Turn the
beep tone ON;
IC-A14:
Push
[FUNC]
, then push
[BEEP](8)
.
p. 22
IC-A14S:
Turn the beep tone ON in set mode.
pgs. 22
, 25
D
CP-22 fuse replacement
If the fuse blows or the receiver stops functioning while oper-
ating with the optional CP-22
CIGARETTE
LIGHTER
CABLE
, find
the source of the problem if possible, and replace the dam-
aged fuse with a new rated one (FGB 8 A) as shown right.
Fuse 8 A