Icom ID-52A Basic Manual english - Page 18

INITIAL SETUP, Attaching the Battery pack

Get Icom ID-52A PDF manuals and user guides View all Icom ID-52A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

2 INITIAL SETUP Before starting using the transceiver, follow these steps for the initial setup. STEP 1 Attaching the battery pack and charging the battery. (pp. 5, 6) STEP 2 Inserting a microSD card. (p. 7) STEP 3 Turning ON the transceiver. (p. 7) STEP 4 Adjusting the audio level. (p. 7) STEP 5 Saving your initial setting onto a microSD card. (p. 8) STEP 6 Confirming the GPS signal receiving. (p. 10) STEP 7 * Entering your Call sign (MY) into the transceiver. (p. 45) STEP 8 * Registering your call sign at a Gateway repeater. (p. 47) ► You have completed the steps!! * You can skip the steps if you do not plan to operate D-STAR right now. ■■ Attaching the Battery pack Attach or detach the battery pack or battery case, as illustrated below. LL When attaching, slide the battery pack and hold it down until the both latches are locked. To attach To detach 2 1 Battery pack or battery case 1 1 2 LL Illustrations are when using the battery pack. NOTE: ••Even when the transceiver is OFF, a slight current still flows in the circuits. Remove the battery pack or case from the transceiver when not using it for a long time. Otherwise, the attached battery pack or case will become exhausted, and will need to be recharged or replaced. ••When the temperature is around 0°C (32°F) or below, the Battery Protection function automatically sets the transceiver power to Low1 power (0.5 W), and disables power selections High, Mid, and Low2. 5 BASIC MANUAL

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
5
BASIC MANUAL
2
INITIAL SETUP
Before starting using the transceiver, follow these steps for the initial setup.
STEP 1
Attaching the battery pack and charging the battery. (pp. 5, 6)
STEP 2
Inserting a microSD card. (p. 7)
STEP 3
Turning ON the transceiver. (p. 7)
STEP 4
Adjusting the audio level. (p. 7)
STEP 5
Saving your initial setting onto a microSD card. (p. 8)
STEP 6
Confirming the GPS signal receiving. (p. 10)
STEP 7
* Entering your Call sign (MY) into the transceiver. (p. 45)
STEP 8
* Registering your call sign at a Gateway repeater. (p. 47)
► You have completed the steps!!
* You can skip the steps if you do not plan to operate D-STAR right now.
■
Attaching the Battery pack
Attach or detach the battery pack or battery case, as illustrated below.
L
When attaching, slide the battery pack and hold it down until the both latches are locked.
1
1
2
2
1
Battery pack or
battery case
L
Illustrations are when using the battery pack.
NOTE:
•
Even when the transceiver is OFF, a slight current still flows in the circuits. Remove the
battery pack or case from the transceiver when not using it for a long time. Otherwise, the
attached battery pack or case will become exhausted, and will need to be recharged or
replaced.
•
When the temperature is around 0°C (32°F) or below, the Battery Protection function
automatically sets the transceiver power to Low1 power (0.5 W), and disables power
selections High, Mid, and Low2.
To attach
To detach