Icom ID-52A Basic Manual english - Page 78

When receiving no reply

Get Icom ID-52A PDF manuals and user guides View all Icom ID-52A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 78 highlights

D-STAR OPERATION ■■ When receiving no reply To communicate through the repeater, your signal must access to the repeater. The following chart is designed to help you correct problems which are not equipment malfunctions. LL "AM" indicates the PDF type Advanced manual. PROBLEM POSSIBLE CAUSE SOLUTION REF. After your call, the repeater does not return a status reply. The repeater setting is wrong. Select the correct repeater. Correct the repeater frequency, frequency offset, or duplex settings. p. 51 - Your transmission did not reach the repeater. Wait until you are closer to the repeater and try again. - Try to access another repeater. - After your call, the The call was successfully Wait for a while, and try repeater replies 'UR?' sent, but no station again. - and its call sign. immediately replied. After your call, the Your own call sign (MY) has repeater replies 'RX' or not been set. 'RPT?' and the access repeater's call sign. Your own call sign (MY) has not been registered on a gateway repeater, or the registered contents do not match your transceiver's settings. Set your own call sign (MY). p. 45 Register your own call sign (MY) on a gateway repeater, or confirm the registration of the call sign. p. 47 After your call, the repeater replies 'RPT?' and the access repeater's call sign. The call sign of the destination repeater is wrong. Correctly set the destination - repeater call sign. After your call, the The repeater cannot connect Check the repeater settings. repeater replies 'RPT?' to the destination repeater. and the destination repeater's call sign. The repeater is busy. - Wait for a while, and try it again. Even holding down There is no repeater list in [DR], the DR screen is your transceiver. not displayed. Import the repeater using a microSD card. p. 66 Directly enter the Repeater list data into the transceiver. AM The Lock function is activated. Hold down [ ] for 1 second to turn OFF the Lock p. 20 function. D-STAR GUIDE 65

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
D-STAR OPERATION
65
D-STAR GUIDE
■
When receiving no reply
To communicate through the repeater, your signal must access to the repeater. The
following chart is designed to help you correct problems which are not equipment
malfunctions.
“AM” indicates the PDF type Advanced manual.
PROBLEM
POSSIBLE CAUSE
SOLUTION
REF.
After your call, the
repeater does not
return a status reply.
The repeater setting is
wrong.
Select the correct repeater.
p. 51
Correct the repeater
frequency, frequency offset,
or duplex settings.
—
Your transmission did not
reach the repeater.
Wait until you are closer to
the repeater and try again.
—
Try to access another
repeater.
—
After your call, the
repeater replies ‘UR?’
and its call sign.
The call was successfully
sent, but no station
immediately replied.
Wait for a while, and try
again.
—
After your call, the
repeater replies ‘RX’ or
‘RPT?’ and the access
repeater’s call sign.
Your own call sign (MY) has
not been set.
Set your own call sign (MY).
p. 45
Your own call sign (MY)
has not been registered on
a gateway repeater, or the
registered contents do not
match your transceiver’s
settings.
Register your own call sign
(MY) on a gateway repeater,
or confirm the registration of
the call sign.
p. 47
After your call, the
repeater replies
‘RPT?’ and the access
repeater’s call sign.
The call sign of the
destination repeater is
wrong.
Correctly set the destination
repeater call sign.
—
After your call, the
repeater replies ‘RPT?’
and the destination
repeater’s call sign.
The repeater cannot connect
to the destination repeater.
Check the repeater settings.
—
The repeater is busy.
Wait for a while, and try it
again.
Even holding down
[DR], the DR screen is
not displayed.
There is no repeater list in
your transceiver.
Import the repeater using a
microSD card.
p. 66
Directly enter the Repeater
list data into the transceiver.
AM
The Lock function is
activated.
Hold down [
] for 1
second to turn OFF the Lock
function.
p. 20