Intel D815EEA2U Product Guide - Page 29

Intel D815EEA2U - P3 Socket 370 ATX Motherboard Manual

Get Intel D815EEA2U - P3 Socket 370 ATX Motherboard PDF manuals and user guides
UPC - 735858146135
View all Intel D815EEA2U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Installing and Replacing Desktop Board Components Observe the precautions in "Before You Begin" on page 25. Place the desktop board on top of an ESD safe surface, component-side up. Follow the steps outlined below to attach the RM (A) to the AGP universal connector (B): 1. Locate the AGP connector (J6C1) on the desktop board as shown in Figure 6. Note that the desktop board's silkscreen (C) indicates the correct final position of the lever (E) on the RM. A E D C B OM11624 Figure 6. AGP Connector Location and Retention Mechanism (RM) Placement (Inset) (the D815EEA2 Board Is Shown) 2. Position the RM over the AGP universal connector as shown below. OM10111 3. Push the lever end of the RM in the direction of the arrow until the two rearmost tabs (D) spread over the end of the AGP universal connector. OM10180 4. Push the free end of the RM over the other end of the AGP connector and press down evenly on both ends of the RM until all four tabs click underneath the AGP universal connector. Do not apply unnecessary pressure to avoid damaging the board. OM10181 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
Installing and Replacing Desktop Board Components
29
Observe the precautions in “Before You Begin” on page 25.
Place the desktop board on top of an
ESD safe surface, component-side up.
Follow the steps outlined below to attach the RM (A) to the
AGP universal connector (B):
1.
Locate the AGP connector (J6C1) on the desktop board as shown in Figure 6.
Note that the
desktop board’s silkscreen (C) indicates the correct final position of the lever (E) on the RM.
OM11624
C
B
A
D
E
Figure 6.
AGP Connector Location and Retention Mechanism (RM) Placement (Inset)
(the D815EEA2 Board Is Shown)
2.
Position the RM over the AGP universal connector as shown below.
OM10111
3.
Push the lever end of the RM in the direction of the arrow until the two rearmost tabs (D)
spread over the end of the AGP universal connector.
OM10180
4.
Push the free end of the RM over the other end of the AGP connector and press down evenly
on both ends of the RM until all four tabs click underneath the AGP universal connector.
Do
not apply unnecessary pressure to avoid damaging the board.
OM10181