Intel D845PEBT2 Product Guide - Page 30

Installing and Removing an AGP Card, Installing an AGP Card, Removing the AGP Card

Get Intel D845PEBT2 PDF manuals and user guides View all Intel D845PEBT2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

Intel Desktop Board D845PEBT2 Product Guide Installing and Removing an AGP Card CAUTION When installing any AGP card in the desktop board, ensure that it is fully seated in the AGP connector before you power on the system. If the card is not fully seated in the AGP connector, an electrical short may result across the AGP slot pins. Depending on the over-current protection of the power supply, certain board components and/or traces may be damaged. The AGP connector supports 1.5 V 4X and 2X AGP cards. The desktop board has an integrated AGP card retention mechanism (RM). Installing an AGP Card Follow these instructions to install an AGP card: 1. Observe the precautions in "Before You Begin" on page 23. 2. Place the AGP card in the AGP connector. 3. Press down on the card until it is completely seated in the AGP connector and the card retention notch snaps into place around the RM pin. 4. Secure the card's metal bracket to the chassis back panel with a screw. Removing the AGP Card Follow these instructions to remove the AGP card from the RM: 1. Observe the precautions in "Before You Begin" on page 23. 2. Remove the screw (B) that secures the card's metal bracket (A) to the chassis back panel. 3. Push back on the RM lever (D), as shown in Figure 8, until the retention pin (C) completely clears the notch in the card. 4. Pull the card straight up (E). B E A C D Figure 8. Removing the AGP Card OM10595 30

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
Intel Desktop Board D845PEBT2 Product Guide
30
Installing and Removing an AGP Card
CAUTION
When installing any AGP card in the desktop board, ensure that
it is fully seated in the AGP
connector before you power on the system.
If the card is not fully seated in the AGP connector, an
electrical short may result across the AGP slot pins.
Depending on the over-current protection of
the power supply, certain board components and/or traces may be damaged.
The AGP connector supports 1.5 V 4X and 2X AGP cards.
The desktop board has an integrated
AGP card retention mechanism (RM).
Installing an AGP Card
Follow these instructions to install an AGP card:
1.
Observe the precautions in "Before You Begin" on page 23.
2.
Place the AGP card in the AGP connector.
3.
Press down on the card until it is completely seated in the AGP connector and the card
retention notch snaps into place around the RM pin.
4. Secure the card
’
s metal bracket to the chassis back panel with a screw.
Removing the AGP Card
Follow these instructions to remove the AGP card from the RM:
1.
Observe the precautions in "Before You Begin" on page 23.
2.
Remove the screw (B) that secures the card
’
s metal bracket (A) to the chassis back panel.
3.
Push back on the RM lever (D), as shown in Figure 8, until the retention pin (C) completely
clears the notch in the card.
4.
Pull the card straight up (E).
OM10595
A
B
C
D
E
Figure 8.
Removing the AGP Card