Home » Intel Manuals » Processors » Intel X5472 » Manual Viewer

Intel X5472 Data Sheet - Page 118

Mechanical Considerations, Electrical Considerations

UPC - 735858201551

Add to My Manuals
Save this manual to your list of manuals

Page 118 highlights

Debug Tools Specifications 9.3.1 9.3.2 Mechanical Considerations The LAI is installed between the processor socket and the processor. The LAI plugs into the socket, while the processor plugs into a socket on the LAI. Cabling that is part of the LAI egresses the system to allow an electrical connection between the processor and a logic analyzer. The maximum volume occupied by the LAI, known as the keepout volume, as well as the cable egress restrictions, should be obtained from the logic analyzer vendor. System designers must make sure that the keepout volume remains unobstructed inside the system. Note that it is possible that the keepout volume reserved for the LAI may include differerent requirements from the space normally occupied by the heatsink. If this is the case, the logic analyzer vendor will provide a cooling solution as part of the LAI. Electrical Considerations The LAI will also affect the electrical performance of the FSB, therefore it is critical to obtain electrical load models from each of the logic analyzer vendors to be able to run system level simulations to prove that their tool will work in the system. Contact the logic analyzer vendor for electrical specifications and load models for the LAI solution they provide. § 118

Section	Page
Quad-Core Intel® Xeon® Processor 5400 Series	1
1 Introduction	9
1.1 Terminology	10
1.2 State of Data	13
1.3 References	13
2 Quad-Core Intel® Xeon® Processor 5400 Series Electrical Specifications	15
2.1 Front Side Bus and GTLREF	15
2.2 Power and Ground Lands	16
2.3 Decoupling Guidelines	16
2.3.1 VCC Decoupling	16
2.3.2 VTT Decoupling	16
2.3.3 Front Side Bus AGTL+ Decoupling	16
2.4 Front Side Bus Clock (BCLK[1:0]) and Processor Clocking	17
2.4.1 Front Side Bus Frequency Select Signals (BSEL[2:0])	17
2.4.2 PLL Power Supply	18
2.5 Voltage Identification (VID)	18
2.6 Reserved, Unused, and Test Signals	21
2.7 Front Side Bus Signal Groups	22
2.8 CMOS Asynchronous and Open Drain Asynchronous Signals	24
2.9 Test Access Port (TAP) Connection	24
2.10 Platform Environmental Control Interface (PECI) DC Specifications	24
2.10.1 DC Characteristics	24
2.10.2 Input Device Hysteresis	25
2.11 Mixing Processors	26
2.12 Absolute Maximum and Minimum Ratings	26
2.13 Processor DC Specifications	27
2.13.1 Flexible Motherboard Guidelines (FMB)	27
2.13.2 VCC Overshoot Specification	38
2.13.3 Die Voltage Validation	39
2.14 AGTL+ FSB Specifications	39
3 Mechanical Specifications	43
3.1 Package Mechanical Drawings	43
3.2 Processor Component Keepout Zones	47
3.3 Package Loading Specifications	47
3.4 Package Handling Guidelines	48
3.5 Package Insertion Specifications	48
3.6 Processor Mass Specifications	48
3.7 Processor Materials	48
3.8 Processor Markings	48
3.9 Processor Land Coordinates	49
4 Land Listing	51
4.1 Quad-Core Intel® Xeon® Processor 5400 Series Pin Assignments	51
4.1.1 Land Listing by Land Name	51
4.1.2 Land Listing by Land Number	61
5 Signal Definitions	71
5.1 Signal Definitions	71
6 Thermal Specifications	79
6.1 Package Thermal Specifications	79
6.1.1 Thermal Specifications	79
6.1.2 Thermal Metrology	90
6.2 Processor Thermal Features	90
6.2.1 Intel® Thermal Monitor Features	90
6.2.2 On-Demand Mode	92
6.2.3 PROCHOT# Signal	93
6.2.4 FORCEPR# Signal	93
6.2.5 THERMTRIP# Signal	94
6.3 Platform Environment Control Interface (PECI)	94
6.3.1 Introduction	94
6.3.2 PECI Specifications	96
7 Features	97
7.1 Power-On Configuration Options	97
7.2 Clock Control and Low Power States	97
7.2.1 Normal State	98
7.2.2 HALT or Extended HALT State	98
7.2.3 Stop-Grant State	100
7.2.4 Extended HALT Snoop or HALT Snoop State, Stop Grant Snoop State	101
7.3 Enhanced Intel SpeedStep® Technology	101
8 Boxed Processor Specifications	103
8.1 Introduction	103
8.2 Mechanical Specifications	105
8.2.1 Boxed Processor Heat Sink Dimensions (CEK)	105
8.2.2 Boxed Processor Heat Sink Weight	113
8.2.3 Boxed Processor Retention Mechanism and Heat Sink Support (CEK)	113
8.3 Electrical Requirements	113
8.3.1 Fan Power Supply (Active CEK)	113
8.3.2 Boxed Processor Cooling Requirements	114
8.4 Boxed Processor Contents	115
9 Debug Tools Specifications	117
9.1 Debug Port System Requirements	117
9.2 Target System Implementation	117
9.2.1 System Implementation	117
9.3 Logic Analyzer Interface (LAI)	117
9.3.1 Mechanical Considerations	118

Match case Limit results 1 per page

Debug Tools Specifications

118

9.3.1

Mechanical Considerations

The LAI is installed between the processor socket and the processor. The LAI plugs into

the socket, while the processor plugs into a socket on the LAI. Cabling that is part of

the LAI egresses the system to allow an electrical connection between the processor

and a logic analyzer. The maximum volume occupied by the LAI, known as the keepout

volume, as well as the cable egress restrictions, should be obtained from the logic

analyzer vendor. System designers must make sure that the keepout volume remains

unobstructed inside the system. Note that it is possible that the keepout volume

reserved for the LAI may include differerent requirements from the space normally

occupied by the heatsink. If this is the case, the logic analyzer vendor will provide a

cooling solution as part of the LAI.

9.3.2

Electrical Considerations

The LAI will also affect the electrical performance of the FSB, therefore it is critical to

obtain electrical load models from each of the logic analyzer vendors to be able to run

system level simulations to prove that their tool will work in the system. Contact the

logic analyzer vendor for electrical specifications and load models for the LAI solution

they provide.