Invacare M91R Owners Manual - Page 65

Tilting the Seat Assembly Forward

Get Invacare M91R PDF manuals and user guides View all Invacare M91R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

5 WHEELCHAIR OPERATION 8. Remove prop rod from the clip located on the Formula PTO Plus frame and engage the prop rod end into the front seat post as shown in FIGURE 15. 9. Gently allow weight of seat assembly to be supported by the prop rod.  Only leave the seat assembly in the up/open position while performing any necessary procedures. Always lower the seat assembly to the down/closed position when not servicing the wheelchair and ensure it is in the locked position before using. Tilting the Seat Assembly Forward 1. Using one hand, firmly grasp the front edge of the seat assembly and lift until seat assembly is no longer supported by the prop rod. 2. Disengage the prop rod from the front seat post and secure into clip. 3. Using both hands, slowly tilt the seat assembly Forward into the Down/Closed position. ƽ WARNING Ensure the two screws are fully engaged and the Formula PTO Plus frame is securely locked in place before use - otherwise injury or damage may result. Formula PTO Plus Frame Front Seat Post Screw Washer Mounting Hole Clip 4. Insert the two screws through the washers, the Formula PTO Plus frame and the two front seat posts. Prop Rod FIGURE 15 Tilting the Seat Assembly Part No 1143153 65 Invacare® Pronto® M91™

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
5
WHEELCHAIR OPERATION
Part No 1143153
65
Invacare® Pronto® M91™
8.
Remove prop rod from the clip located on the Formula PTO Plus frame and engage the prop rod end into the front seat post as shown in
FIGURE 15.
9.
Gently allow weight of seat assembly to be supported by the prop rod.
Tilting the Seat Assembly Forward
1.
Using one hand, firmly grasp the front edge of the seat assembly and
lift until seat assembly is no longer supported by the prop rod.
2.
Disengage the prop rod from the front seat post and secure into
clip.
3.
Using both hands, slowly tilt the seat assembly Forward into the
Down/Closed position.
4.
Insert the two screws through the washers, the Formula PTO Plus
frame and the two front seat posts.
FIGURE 15
Tilting the Seat Assembly
Only leave the seat assembly in the up/open position while performing any necessary procedures. Always lower the seat
assembly to the down/closed position when not servicing the wheelchair and ensure it is in the locked position before using.
±
WARNING
Ensure the two screws are fully engaged and the
Formula PTO Plus frame is securely locked in
place before use - otherwise injury or damage may
result.
Formula PTO Plus Frame
Screw
Washer
Prop Rod
Clip
Front Seat Post
Mounting
Hole